Xerox WorkCentre 5687 Series Service Manual page 2202

Table 6 Input codes 09
Code Displayed Name Description
09-074 Transfer / Detack Stall Transfer / detack cleaner head stall
Sensor sensor.
The stall sensor is a electrical
device within the motor control on
the IOT PWB.
09-310 Low Toner Sensor Low toner sensor (Q09-310)
09-350 Waste Toner Full Sen- Waste toner full sensor(Q09-350)
sor detects when waste toner reaches
a certain level in the container.
09-360 Toner Conc. Sensor Toner concentration sensor (Q09-
360)
09-365 Humidity Sensor Relative humidity sensor (Q09-365) Displays RH%
09-370 Dev. Temp. Sensor Developer temperature sensor
(Q09-370)
09-375 Ambient Temp. Sensor Ambient temperature sensor (Q09-
375)
09-380 Waste Toner Door Sw Waste toner door switch (S09-380)
detects if the waste bottle is miss-
ing or the door is open during run
Table 7 Input codes 10
Code Displayed Name Description
10-100 Fuser Exit Switch Fuser exit switch (S10-100),
detects when paper exits the fuser
10-105 Invert Sensor Inverter sensor (Q10-105), detects
when paper enters the inverter
10-120 IOT Exit Sensor IOT exit sensor (Q10-120), detects
when paper exits the IOT
10-300 Fuser Temp Sensor A Displays current thermistor values.
Converts input resistance of ther-
mistors and shows A-D conversion.
10-310 Fuser Temp Sensor B Displays current thermistor values.
Converts input resistance of ther-
mistors and shows A-D conversion.
10-315 Fuser Temp Fault Snr Detects fault in fuser thermistor.
Table 8 Input codes 11
Code Displayed Name Description
11-035 Bin 1 Empty Sensor HCSS BM bin 1 empty sensor
(Q11-035)
General Procedures & Information
dC330
Code Displayed Name
General
11-044 Punch Unit Home
High = actuated, Low =
Sensor
not actuated
Stack with transfer / 11-100 Entry Sensor
detack corotron cleaner
motor stall sensor,
11-110 Punch Sensor
motor forward and
motor reverse
11-112 Chad Bin Set Sensor HVF chad bin set sensor (Q11-112)
High = toner in sump,
low = toner depleted
11-120 Compiler Sensor
High = container full,
low = container not full
11-130 Top Exit Sensor
Displays toner concen-
tration level in %
11-140 2nd to Top Exit Snr
Displays temperature in
11-150 Inserter Sheet Size
degrees C
Detector 1
Displays temperature in
degrees C
High = bottle present/
11-151 Inserter Sheet Size
door closed, low = bottle
Detector 2
missing/door open
11-152 Inserter STS Sheet
General
Size Detector
High = paper present,
low = no paper
High = paper present, 11-153 Inserter Unit Empty
Sensor
low = no paper
High = paper present,
low = no paper 11-154 Inserter LE Sensor
0-255 degrees C.
11-155 Inserter TE Sensor
11-156 Inserter Bottom Plate
0-255 degrees C.
Sensor
High = fault low = good 11-157 Buffer Position Sen-
sor
11-158 HVF Booklet Exit
Sensor
General
High = bin empty, low =
11-159 Nip Home Sensor
bin not empty
August 2007
6-310
Table 8 Input codes 11
Description General
HVF punch unit home sensor (Q11- High = home, low = unit
044) not home
LCSS, HVF and HCSS BM entry High = paper present,
sensor (Q11-100) low = no paper
LCSS, HVF and HCSS BM punch High = paper present,
position sensor (Q11-110) low = no paper
High = chad bin
detects when the chad bin installed installed
HCSS BM Compiler sensor (Q11- High = paper present,
120) detects when paper enters the low = no paper
compiler carriage
LCSS, HVF and HCSS BM top exit High = paper present,
sensor (Q11-130) low = no paper
LCSS, HVF and HCSS BM 2nd to High = paper present
top exit sensor (Q11-140) detects low = no paper
paper exiting to the bin (bin 1)
HVF inserter sheet size detector 1 High = sheet size
(Q11-150) detects the DOF (Direc- detected
tion Of Feed) sheet size in inserter
tray
HVF inserter sheet size detector 2 High = sheet size
(Q11-151) detects the DOF (Direc- detected
tion Of Feed) sheet size in inserter
tray
HVF inserter STS (Side To Side) High = sheet size
sheet size detector (Q11-152) detected
detects STS (Side To Side) sheet
size in inserter tray
HVF inserter unit empty sensor High = paper present,
(Q11-153) detects paper present low = no paper
inserter tray
HVF inserter LE sensor (Q11-154) High = LE detected, low
detects the LE of the paper = LE not detected
HVF inserter TE sensor (Q11-155) High = TE detected, low
detects the TE of the paper = TE not detected
HVF inserter bottom plate sensor High = home position,
(Q11-156) detects the bottom plate low = not home
in home position
HVF Buffer position sensor (Q11- High = paper present,
157) detects paper low = no paper
HVF booklet exit sensor (Q11-158) High = paper present,
detects paper exiting the finisher to low = no paper
enter into booklet maker
HVF nip home sensor (Q11-159) High = Nip home
detects the position of the buffer
movement tray in descending
WorkCentre 5687 Family