Xerox WorkCentre 5687 Series Service Manual page 2204

Table 8 Input codes 11
Code Displayed Name Description
11-306 Inserter Top Cover HVF inserter top cover interlock
Intlk sensor (Q11-306) detects if inserter
tray top cover is closed
11-310 Tamp Front Home Snr LCSS, HVF and HCSS BM front
tamper home sensor (Q11-310)
Detect if front tamper is home
11-311 Tamp Rear Home Snr LCSS, HVF and HCSS BM rear
tamper home sensor (Q11-311),
detects if rear tamper is home
11-313 CC 90% Full Sensor HCSS BM compiler carriage 90%
full sensor (Q11-313), detects when
the stack in bin1 or bin 2 is 90% full
11-314 CC Bin Height Sensor HCSS BM compiler carriage bin
height sensor (Q11-314), detects
the height of the paper stack in bin1
or bin 2
11-315 CC Upper Limit HCSS BM compiler carriage upper
Switch limit switch (S11-315) detects the
upper limit of compiler carriage
travel
11-316 CC Lower Limit HCSS BM compiler carriage lower
Switch limit switch (S11-316) detects the
lower limit of compiler carriage
travel
11-317 CC Safety Switch HCSS BM compiler carriage safety
switch (S11-317) interrupts +24V to
the compiler carriage when the
eject housing is open
11-319 Tamp Rear Away Snr LCSS and HVF rear tamper away
home sensor (Q11-319), detects if
the rear tamper is at the away
home position
11-320 Ejector Home Sensor HVF and HCSS BM ejector home
sensor (Q11-320) detects the home
(closed) position of the ejector
housing. LCSS ejector home sen-
sor (Q11-320) detects the home
position of the ejector assembly
11-322 Ejector Out Sensor LCSS and HVF Ejector out sensor
(Q11-322) detects the out position
of the ejector assembly
11-326 Paddle Roll Home LCSS paddle roll position sensor,
Snr HVF and HCSS BM paddle roll
home sensor (Q11-326) detects the
home position of the paddle roll
General Procedures & Information
dC330
General Code Displayed Name
High = made, low = not 11-330 Bin0 90% Full Sensor HCSS BM bin 0 90% full sensor
detected
High = home, low = not 11-331 Bin 1 90% Full Sen-
home sor
high = home, low - not 11-332 Bin 1 Upper Level Snr LCSS and HVF bin 1 upper level
home
High = stack sensed, 11-333 Bin 1 Lower Level Snr LCSS bin 1 lower level sensor
low = stack not sensed
High = stack sensed, 11-334 Bin 1 Upper Limit SW LCSS, HVF and HCSS BM bin 1
low = stack not sensed
11-335 Bin 1 Lower Limit SW LCSS, HVF and HCSS BM bin 1
High = carriage
detected, low = car-
riage not detected
11-336 Bin 1 Mot Encoder
Snr
High = carriage
detected, low = car-
11-337 Bin1 Offset Sensor
riage not detected
High = +24V supplied
low = +24V not supplied
11-348 Chad Bin Lvl Sensor
High = away home, low
= not away home
11-350 Punch Head Home
Snr
High = home, low = not
home
11-351 Punch Hd Present
Snr
11-360 SH 1 Home Sensor
High = out, low= not out
11-361 SH 1 Paper Sensor
High = home, low = not
home
August 2007
6-312
Table 8 Input codes 11
Description General
High = 90% or more full,
(Q11-330) detects when bin 0 is low = less than 90% full
90% or more full
LCSS, HVF and HCSS BM bin 1 High = 90% or more full,
90% full sensor (Q11-331) detects low = less than 90% full
when bin 1 is 90% or more full
High = stack sensed,
sensor (Q11-332) detects the top of low = stack not sensed
the paper stack in bin 1
High = stack sensed,
(Q11-333) detects the top of the low = stack not sensed
paper stack in bin 1
High = bin detected, low
upper limit switch (S11-334) detects = bin not detected
the upper limit of bin 1 movement
High = bin detected, low
upper limit switch (S11-335) detects = bin not detected
the lower limit of bin 1 movement
LCSS bin 1 motor encoder sensor High = bar in encoder
(Q11-336) generates motor speed wheel, low = gap in
pulses encoder wheel
HVF and HCSS BM bin 1 offset High = tray moving from
sensor (Q11-337) detects the offset home to offset, low =
and home position of bin 1 tray moving from offset
to home
LCSS, HVF and HCSS BM chad High = bin full, low = bin
bin full sensor (Q11-348) detects not full
when the weight of the chad
reaches a pre-set value
LCSS, HVF and HCSS BM punch High = punch home, low
head home sensor (Q11-350) = punch not home
detects the home position of the
punch head
LCSS punch head present sensor High = punch installed,
(Q11-351) detects if a hole punch is low = punch not
installed installed
LCSS, HVF and HCSS BM staple High = home, low = not
head 1 home sensor (Q11-360) home
detects when the staple head is
fully open (home position)
LCSS, HVF and HCSS BM staple High = paper present,
head 1 paper present sensor (Q11- low = no paper
361) detects when paper is within
the jaws of the stapler
WorkCentre 5687 Family