Xerox WorkCentre 5687 Series Service Manual page 1971

Table 8 NVM chain 9
Location NVM Name NVM Description
09-064 FRU Total Count Backup of CRU data: FRU
total count.
09-065 XRU PR Cycle Backup of CRU data: XRU
Count P/R cycle count.
09-066 FRU Web Usage Backup of CRU data: FRU
Count xeb usage count.
09-068 TC Setpoint Sets target TC for devel-
oper process controls.
09-069 TCSensorCtrtVolt- Sets TC sensor control volt-
age age to adjust sensitivity.
09-070 TCSetupCom- TC setup completed.
pleted
09-073 Last Pixel Count Cumulative Pixel Count
over the last TC control
block (20 prints).
09-083 ReplenCart- Maximum continuous run
MotRun period.
09-087 Rep Cartridge Toner (replenisher) car-
Empty tridge empty status.
09-090 Waste Full Thresh- Waste Full Print Count at
old which 'Bottle Full' status is
confirmed.
09-093 Waste Shutdown Maximum number of prints
Limit allowed post waste full
before shutdown.
09-096 Developer Temp Actual developer temp as
measured by sensor.
09-097 Humidity% RH Actual machine humidity as
measured by sensor.
09-098 Altitude Altitude adjustment in
metres.
09-100 Main Motor Delay Enables or disables a delay
Flag to the main motor and pho-
toreceptor motor run up
times by adding 1150 to
both of the read NVM val-
ues for IOT NVM.
09-101 Ambient Temp Actual ambient temp as
measured by sensor.
WorkCentre 5687 Family
Value Default Location NVM Name
0 Read only 0 09-110
0 Read only 0
09-111
0 Read only 0
09-112
0 0
09-114
400 to 1200 800
(mVx10) 09-115
0 or 1 0 09-116
0 Read only 0 09-117
09-118
15 to 40 ms 30
09-119
0 or 1 0
1 to 1000 prints 32/38/45=0 09-120
55/65/75/
87=100
0 to 10000 32/38/45=0 09-121
prints 55/65/75/
87=1000
Degrees C. 0
%RH 0
09-122
0 = zero to 0
749m
1 = 750 to
1499m
2 = 1500 to
09-123
2249m
3 = 2250 to
2999m 09-124
4 = 3000+m
0=disabled 0 09-125
1=enabled
09-126
09-127
Degrees C 0
August 2007
6-79
Table 8 NVM chain 9
NVM Description
Replenisher Replenisher capacity.
capacity
Repl. Delivery Replenisher delivery rate.
Rate
Cumulative Disp Total dispense time.
Time
Rep Lev Snr Fault Flag to indicate replenisher
sensor failure.
TC Sensor Fault TC sensor fault.
Paper path fans Paper path cooling mode.
mode
Scorotron On Charge scorotron ON cycle
Ramp Up in ramp up.
Dev bias On Ramp Developer bias ON cycle in
Up ramp up.
GridV Off Ramp Charge scorotron grid volt-
Dwn age OFF cycle out ramp
down.
Ozone max life Stores the maximum prints
to make with the current
ozone filter.
Man Cleaning Charge Scorotron Manual
Interval Cleaning Interval. Fre-
quency in K sheets for
when a manual scorotron
cleaning request is dis-
played.
Auto Cleaning Charge Scorotron Auto
Interval Cleaning Interval. Fre-
quency in K sheets for
when a manual scorotron
cleaning request is dis-
played.
Num Images Number of images deliv-
Delivered ered.
InactivityLimit The set limit of machine
inactivity in minutes
Dev Bias Off Developer bias OFF cycle
Ramp Dwn out ramp down.
Dev Bias Off Developer bias OFF cycle
Ramp Dwn Alt out ramp down alternative.
Dev Bias Off FS Developer bias OFF fast
Ramp Dwn Alt shutdown cycle out ramp
down.
Value Default
1050 to 1787 32/38/45/
grams 55=1188
65/75/87=1750
15 to 60 35/45/55=460
decigrams/min 65/75/87=550
0 to 0
78000000ms
0 0
0 0
0=disabled 32/38/45/55=0
1=enabled 65/75/87=1
0 to 1000ms 100
0 to 1000ms 160
0 to 1000ms 32/38=80
45/55/65/75/
87=120
0 to 350k
4294967295
2 to 50 25k
2 to 50 20k
0 to 0
4294967295
120 to 4320 300
0 to 1000ms 160
0 to 1000ms 32/38/45/55=0
65/75/87=100
0 to 1000ms 32/38/45/55=0
65/75/87=100
General Procedures & Information
dC131a