Xerox WorkCentre 5687 Series Service Manual page 2211

Table 21 Output codes 20
Code Displayed Name Description
20-093 DTMF 1 Line2 Emits DTMF 1on line 2
20-094 DTMF 2 Line2 Emits DTMF 2 on line 2
20-095 DTMF 3 Line2 Emits DTMF 3 on line 2
20-096 DTMF 4 Line2 Emits DTMF 4 on line 2
20-097 DTMF 5 Line2 Emits DTMF 5 on line 2
20-098 DTMF 6 Line2 Emits DTMF 6 on line 2
20-099 DTMF 7 Line2 Emits DTMF 7 on line 2
20-100 DTMF 8 Line2 Emits DTMF 8 on line 2
20-101 DTMF 9 Line2 Emits DTMF 9 on line 2
20-102 DTMF A Line2 Emits DTMF A on line 2
20-103 DTMF B Line2 Emits DTMF B on line 2
20-104 DTMF C Line2 Emits DTMF C on line 2
20-105 DTMF D Line2 Emits DTMF D on line 2
20-110 V.21 300 bps Line2 Emits V.21 300 bps on line 2
20-111 V.27ter 2400 bps Line2 Emits V.27ter 2400 bps on line 2
20-112 V.27ter 4800 bps Line2 Emits V.27ter 4800 bps on line 2
20-113 V.29 7200 bps Line2 Emits V.29 7200 bps on line 2
20-114 V.29 9600 bps Line2 Emits V.29 9600 bps on line 2
20-115 V.17 7200 bps Line2 Emits V.17 7200 bps on line 2
20-116 V.17 9600 bps Line2 Emits V.17 9600 bps on line 2
20-117 V.17 12000 bps Line2 Emits V.17 12000 bps on line 2
20-118 V.17 14400 bps Line2 Emits V.17 14400 bps on line 2
20-119 V.34 2400 bps Line2 Emits V.34 2400 bps on line 2
20-120 V.34 4800 bps Line2 Emits V.34 4800 bps on line 2
20-121 V.34 7200 bps Line2 Emits V.34 7200 bps on line 2
20-122 V.34 9600 bps Line2 Emits V.34 9600 bps on line 2
20-123 V.34 12000 bps Line2 Emits V.34 12000 bps on line 2
20-124 V.34 14400 bps Line2 Emits V.34 14400 bps on line 2
20-125 V.34 16800 bps Line2 Emits V.34 16800 bps on line 2
20-126 V.34 19200 bps Line2 Emits V.34 19200 bps on line 2
20-127 V.34 21600 bps Line2 Emits V.34 21600 bps on line 2
20-128 V.34 24000 bps Line2 Emits V.34 24000 bps on line 2
20-129 V.34 26400 bps Line2 Emits V.34 26400 bps on line 2
20-130 V.34 28800 bps Line2 Emits V.34 28800 bps on line 2
20-131 V.34 31200 bps Line2 Emits V.34 31200 bps on line 2
20-132 V.34 33600 bps Line2 Emits V.34 33600 bps on line 2
WorkCentre 5687 Family
dC502 DADH Width Guide Calibration Procedure
General
Purpose
On/off
To recalibrate the DADH width guides, so that the correct document size can be determined
On/off
from the analogue width guide potentiometer. Refer to dC604 for registration setup.
On/off
On/off
Calibration is only necessary if:
On/off
• The values in the image processor NVM have not been set and are still zero.
On/off
• A new component has been installed to the DADH input tray.
On/off
On/off
• The characteristics of the potentiometer have changed.
On/off
If the calibration routine is not performed the image processor NVM values will be zero. This
On/off
will force the DADH to use the average values programmed into DADH flash memory during
On/off
manufacture.
On/off
On/off Description
On/off
An A4 LEF or 8.5" x 11" LEF document is placed in the DADH input tray and the width guides
On/off
adjusted to the same width as the document. The A to D value (maximum to minimum width in
On/off
mm) is derived from the width guide potentiometer and the process is repeated for an A5 SEF
On/off
or 8.5" x 5.5" SEF size document.
On/off
On/off
The two calibration values are stored in the image processor's NVM. They are passed to the
On/off
DADH together with the market paper size setting whenever a Reset command is given (this
instructs the DADH to set all the output ports to their default off condition and to provide an
On/off
On/off update of any NVM values including the cpm rate). If the image processor NVM values are
within a valid range (Table 1) the DADH will use the two values to establish a linear equation
On/off
that can be used to calculate (in mm) all the other valid document sizes.
On/off
On/off
Procedure
On/off
On/off
1. Enter diagnostics, GP 1.
On/off
2. Select, Diagnostics Routines, Copier Routines, dC502 DADH Width Calibration.
On/off
3. Select and touch the appropriate button to select A4 or 8.5" x 11".
On/off
NOTE: The market paper size setting will default the document size buttons to the rele-
On/off
vant ISO or USA document sizes. Selection of either button will default all the displayed
On/off
document sizes.
On/off
On/off
4. Follow the on-screen instructions.
On/off
5. Touch Exit when routine is completed.
On/off
Table 1 DADH width range
Document size Valid range
A5 SEF 1 to 45
A4 LEF 190 to 237
5.5 x 8.5 SEF 1 to 45
8.5 x 11 LEF 190 to 237
August 2007
6-319
Nominal
31
226
17
203
General Procedures & Information
dC330, dC502