Xerox WorkCentre 5687 Series Service Manual page 2206

Table 8 Input codes 11
Code Displayed Name Description
11-431 Inserter Left Hand HVF Insert left hand door interlock
Door Interlock (Q11-431) detects the state of the
inserter door interlock
Table 9 Input codes 12
Code Displayed Name Description
12-300 OCT Level Sensor OCT 90% full sensor (Q12-300)
detects when tray is 90% or more
full.
12-301 OCT Index Sensor OCT index sensor (Q12-301)
detects the offset and home posi-
tion of bin 1
Table 10 Input codes 14
Code Displayed Name Description
14-100 Carriage Home Sensor Scan carriage home sensor (Q14-
100) detects the home position of
the scan carriage
14-310 DADH Angle Sensor Input module angle sensor (Q14-
310) detects the input module at
30% angle for size sensing.
14-315 Doc Size Sensor 1 Document size sensor 1 (Q14-310) High = document not
14-320 Doc Size Sensor 2 Document size sensor 2 (Q14-314) High = document not
Output Codes
Table 11 Output codes 04
Code Displayed Name Description
04-010 Main motor Drives the pre-registration, registra-
tion, developer, fuser and paper
output modules.
Table 12 Output codes 05
Code Displayed Name Description
05-010 DADH feed sole- DADH feed solenoid (SOL05-010) On/off. 30 seconds timeout
noid
General Procedures & Information
dC330
General
Code Displayed Name Description
High = closed, low =
05-020 DADH feed motor DADH feed motor (MOT05-020)
open
05-025 DADH feed clutch DADH feed clutch (CL05-025)
05-030 DADH CVT motor DADH CVT motor (MOT05-030)
05-050 DADH duplex
solenoid
General
High = 90% or more full,
low = less than 90% full
Code Displayed Name
06-020 ROS Motor Run
High = tray moving from
home to offset, low =
06-025 ROS Motor
tray moving from offset
Standby
to home
Code Displayed Name
General
07-010 T1 Elevate Motor
High - Home, low = not
home
High = input module
07-020 T2 Elevate Motor
lowered, low input mod-
ule raised
sensed, low = document
07-030 T3 Elevate Motor
sensed
sensed, low = document
sensed
07-040 T4 Elevate Motor
07-373 Raise T5 Elevate
Motor
General
On/Off. 60 seconds timeout
07-374 Lower T5 Elevate
Motor
General
August 2007
6-314
Table 12 Output codes 05
General
On/off. 90 seconds time out
On/off. Normally linked with
feed motor. 30 seconds time-
out
On/off. 90 seconds timeout
DADH duplex solenoid (SOL05- On/off. 30 seconds timeout
050)
Table 13 Output codes 06
Description General
Drives ROS motor at run mode On/off. 90 seconds timeout
speed.
Drive ROS motor at standby mode On/off. 90 seconds timeout
speed.
Table 14 Output codes 07
Description General
Energizes the tray 1 elevator motor On/off. Linked to tray 1
(MOT07-010) up. home sensor. Only ener-
gize with tray out. 5 seconds
timeout
Energizes the tray 2 elevator motor On/off. Linked to tray 2
(MOT07-020) up. home sensor. Only ener-
gize with tray out. 5 seconds
timeout
Energizes the tray 3 elevator motor On/off. Linked to tray 3
(MOT07-030) up. home sensor. Only ener-
gize with tray out. 10 sec-
onds timeout
Energizes the tray 4 elevate motor On/off. Linked to tray 4
(MOT07-040) up. home sensor. Only ener-
gies with tray out. 10 sec-
onds timeout
Energizes the tray 5 elevate motor On/off. Only runs while tray
(MOT07-373) to move the tray up. transport limits are not
reached. 10 seconds time-
out
Energizes the tray 5 elevate motor On/off. Only runs while tray
(MOT07-373) to move the tray transport limits are not
down. reached. 10 seconds time-
out
WorkCentre 5687 Family