Xerox WorkCentre 5687 Series Service Manual page 1975

Table 9 NVM chain 10
Location NVM Name NVM Description
10-059 Card stock offset Media type offset for fuser roll
temperature. Unsigned num-
ber in NVM table (displayed
on GUI) to be converted to
signed number. by subtrac-
tion of 10 from table value.
i.e. 8 displayed in NVM is
equivalent to -2 degrees Cel-
sius
10-060 Envelopes Offset Media type offset for fuser roll
temperature. Unsigned num-
ber in NVM table (displayed
on GUI) to be converted to
signed number. by subtrac-
tion of 10 from table value.
i.e. 8 displayed in NVM is
equivalent to -2 degrees Cel-
sius
10-061 Labels Offset Media type offset for fuser roll
temperature. Unsigned num-
ber in NVM table (displayed
on GUI) to be converted to
signed number. by subtrac-
tion of 10 from table value.
i.e. 8 displayed in NVM is
equivalent to -2 degrees Cel-
sius
10-063 Total Fsr Web Total fuser web count.
Count
10-064 Transparency Media type time delay for
delay fuser roll temperature.
10-065 Cardstock delay Media type time delay for
fuser roll temperature.
10-066 Envelopes delay Media type time delay for
fuser roll temperature.
10-067 Labels delay Media type time delay for
fuser roll temperature.
10-068 Tab stock delay Media type time delay for
fuser roll temperature.
10-069 Cold Start Offset Fuser cold start offset profile. 0 to 3
10-070 Cold Roll Offset Fuser cold roll offset profile.
WorkCentre 5687 Family
Value Default Location NVM Name
0 to 25 15 10-071
0 to 30 15 10-072
10-074
10-075
10-102
0 to 30 15
10-122
10-123
10-124
Cycles 0
10-125
0 to 8 seconds 0
0 to 8 seconds 4
10-126
0 to 8 seconds 4
10-328
0 to 8 seconds 4
0 to 8 seconds 4
10-329
32/38/45/
55=0
10-330
65/75/87=2
0 to 11 32/38=1
45/55=6
65/75/87=8
August 2007
6-83
Table 9 NVM chain 10
NVM Description
Rough Stock Off- Media type offset for fuser roll
set temperature. Unsigned num-
ber in NVM table (displayed
on GUI) to be converted to
signed number. by subtrac-
tion of 10 from table value.
i.e. 8 displayed in NVM is
equivalent to -2 degrees Cel-
sius.
Rough Stock Media type time delay for
Delay fuser roll temperature.
Rough Stk FRU Rough Stock Fuser (TOS)
Enable
Type 256 FRU Type 256 Fuser
Enable
Te PFs Toinv Mot Inverter motor off stop posi-
Off Dup tion (simplex).
Te PFs To Inv Mot Time to turn off inverter motor
Off Dup after TE leaves fuser
(duplex).
Fsr Range Temperature range below
standby in which start print
can begin.
Te Inv Snr To Mot Inverter motor off stop posi-
Of SmpS1 tion (simplex).
Te Inv Snr Inv Of Time to turn off inverter motor
Dup Siz 1 after TE leaves inverter sen-
sor for sheets <185mm &
>216mm.
Web Advance Web advance group banding
Group select.
Standby Temp (2) Target temperature during
standby mode.
Run Temp (2) Target temperature during
run mode.
Low Power Temp Target temperature during
(2) power save mode. The low
power simmer temperature is
determined by the Power
Save mode set in Tools.
Value Default
0 to 25 15
0 to 8 seconds 4
Disable = 0 0
Enable = 1
Disable = 0 1
Enable = 1
0 to 800 ms 32/38=530
45/55=360
65/75/87=0
0 to 1200ms 32/38=740
45/55=510
65/75/87=0
10 to 30 deg C 32/38=30
45/55=10
65/75/87=28
0 to 800 ms 32/38=530
45/55=360
65/75/87=200
200 to 1200ms 32/38=740
45/55=510
65/75/87=295
1 = group 1 2
2 = group 2
3 = group 3
10 to 230 deg 32/38=190
C 45/55=195
65/75/87=208
100 to 230 deg 32/38=185
C 45/55=195
65/75/87=203
50 to 150 deg 32/38=85
C 45/55=95
65/75/87=135
General Procedures & Information
dC131a