YASKAWA CIMR-ZU A Series Programming Manual page 374

Inde
Run Command Source ...........................................................88
Run Command Source Selection ............................................. 268
S
S: Special Parameters .................................................... 137, 255
S1: Dynamic Noise Control Function........................................ 255
S2: Sequence Timers ..................................................... 138, 255
S5: HOA Keypad Parameters ................................................. 152
Safety Circuit.................................................................... 146
S-Curve Characteristics ..........................................................53
Search Operation Voltage Limit ................................................51
Secondary PI (PI2) Control.................................................... 142
Secondary PI Disable Mode............................................. 144, 258
Secondary PI Display Digits ............................................ 143, 257
Secondary PI Enable Selection ......................................... 142, 257
Secondary PI Feedback Detection Selection .......................... 145, 259
Secondary PI Feedback High ...................................................93
Secondary PI Feedback Low ....................................................93
Secondary PI High Feedback Detection Time ........................ 145, 259
Secondary PI High Feedback Level .................................... 145, 258
Secondary PI Integral Limit Setting.................................... 144, 258
Secondary PI Integral Time Setting .................................... 143, 258
Secondary PI Low Feedback Detection Level ........................ 144, 258
Secondary PI Low Feedback Detection Time ........................ 145, 258
Secondary PI Output Level Selection .................................. 144, 258
Secondary PI Output Lower Limit ..................................... 144, 258
Secondary PI Output Upper Limit...................................... 144, 258
Secondary PI Proportional Gain Setting ............................... 143, 258
Secondary PI Setpoint Value............................................ 143, 258
Secondary PI Unit Selection ............................................ 143, 258
Secondary PI User Display .............................................. 142, 257
Second Line Monitor Selection ............................................... 131
Selection of Parameter Write during Uv............................... 134, 253
Select PI2 Parameters ............................................................84
Self-Diagnostics.......................................................82, 338, 368
Sequence Timer 1............................................................... 138
Sequence Timer 1 Active ........................................................92
Sequence Timer 1 Day Selection ............................................. 255
Sequence Timer 1 Reference Source......................................... 255
Sequence Timer 1 Selection................................................... 255
Sequence Timer 1 Start Time ................................................. 255
Sequence Timer 1 Stop Time ................................................. 255
Sequence Timer 2 Active ........................................................93
Sequence Timer 2 Day Selection ............................................. 256
Sequence Timer 2 Reference Source......................................... 256
Sequence Timer 2 Selection................................................... 256
Sequence Timer 2 Start Time ................................................. 256
Sequence Timer 2 Stop Time ................................................. 256
Sequence Timer 3 Active ........................................................93
Sequence Timer 3 Day Selection ............................................. 256
Sequence Timer 3 Reference Source......................................... 257
Sequence Timer 3 Selection................................................... 256
Sequence Timer 3 Start Time ................................................. 256
Sequence Timer 3 Stop Time ................................................. 256
Sequence Timer 4 Active ........................................................93
Sequence Timer 4 Day Selection ............................................. 257
Sequence Timer 4 Reference Source......................................... 257
Sequence Timer 4 Selection................................................... 257
Sequence Timer 4 Start Time ................................................. 257
Sequence Timer 4 Stop Time ................................................. 257
7
Sequence Timer Cancel ..........................................................81
Sequence Timer Disable .........................................................81
Sequence Timers 1/2/3/4 Reference Source................................. 141
Sequence Timers 1/2/3/4 Selection........................................... 141
Sequence Timers 1 to 4 Day Selection....................................... 141
Sequence Timers 1 to 4 Start Time........................................... 140
Sequence Timers 1 to 4 Stop Time ........................................... 140
Sequence Timers 2 to 4 ........................................................ 139
Serial Comms Cable Connection Terminal ............... 286, 308, 324, 342
Set Time.................................................................... 136, 254
Short Circuit Brake Time at Start...............................................30
Short Circuit Brake Time at Stop...............................................31
Short Circuit Braking.............................................................83
Short Circuit Braking Current...................................................31
Slave Address ................................................................... 350
Soft Charge Bypass Relay Maintenance..................................... 267
Soft CLA Selection ............................................................. 248
Soft Starter Speed Reference at Previous Fault............................. 265
Software Current Limit Selection ............................................ 122
Software No. (Flash) ........................................................... 264
Software No. (ROM) ........................................................... 264
Speed Agree 1 .....................................................................86
Speed Agree 2 .....................................................................89
Speed Agree Detection Selection............................................. 113
Speed Agreement Detection Level ..................................... 112, 246
Speed Agreement Detection Level (+/-) ............................... 113, 246
Speed Agreement Detection Width .................................... 112, 246
Speed Agreement Detection Width (+/-) .............................. 113, 246
Speed Feedback Detection Control Gain .............................. 127, 251
Speed Feedback Detection Control Gain during ov Suppression ........ 129
Speed Search Deactivation Current ............................................34
Speed Search Deceleration Time ...............................................34
Speed Search Delay Time .......................................................34
Speed Search Detection Compensation Gain .................................35
Speed Search Induced Voltage Level ..........................................37
Speed Search Method Selection ................................................36
Speed Search Method Switching Level (Speed Estimation Type) .........35
Speed Search Restart Current Level............................................36
Speed Search Restart Detection Time..........................................36
Speed Search Selection at Start .................................................34
Speed Search Selection when Run Command is Given during Uv ........37
Speed Search Wait Time.........................................................36
Stall Prevention ................................................................. 106
Stall Prevention Detection Time.............................................. 112
Stall Prevention Level during Acceleration ........................... 108, 245
Stall Prevention Level during Run ..................................... 110, 245
Stall Prevention Limit during Acceleration ........................... 107, 245
Stall Prevention Selection during Acceleration....................... 106, 245
Stall Prevention Selection during Deceleration....................... 108, 245
Stall Prevention Selection during Run ................................. 109, 245
Start Speed Search Select........................................................37
STOP Key Function Selection ................................................ 133
Stopping Method after Communication Error .................. 288, 327, 345
Stopping Method Selection......................................................26
Supported Properties of Objects .............................................. 294
T
T1 Tuning Start ................................................................. 261
T2 Tuning Start ................................................................. 159