Table of Contents
Advertisement
Numerics
2-Wire Initialization .........................................................19
3-Wire Sequence.............................................................75
5th Most Recent Fault..................................................... 265
A
A1-02 (Motor Control Mode) Dependent Parameters ................ 271
Accel/Decel Ramp Hold ....................................................76
Accel/Decel Rate Calculation Gain ..................................... 111
Accel/Decel Time Selection 1 .............................................76
Accel/Decel Time Switching Frequency .................................53
Acceleration/Deceleration Pull-In Current ............................. 128
Acceleration Time ...........................................................52
Acceleration Time Pull-In Current ...................................... 251
Access Level Selection......................................................18
Additional DC Bus Capacitors........................................... 112
Alarm Outputs for Maintenance Monitors ............................. 169
Alarm Register 007FH Contents......................................... 365
Ambient Temperature Setting...................................... 122, 248
Analog Input Filter Time Constant ........................................96
Analog Input Objects...................................................... 295
Analog Input Terminal Enable Selection .................................96
Analog Output Objects.................................................... 295
Analog Terminal Input Selection ..........................................76
Analog Value Objects ..................................................... 295
Automatic Reduction for Stall Prevention during Run ............... 110
Automatic Reduction Selection for Stall Prevention during Run ... 245
AUTO Mode Select .........................................................82
Auto Restart Fault Output Operation Selection........................ 114
Auto Restart Operation Selection........................................ 246
Auto-Tuning Mode Selection ...................................... 156, 261
B
b5-45: PI Output 2 Monitor Minimum....................................49
BACnet Baud Rate ..........................................................73
BACnet Configuration .................................................... 284
BACnet Objects Supported............................................... 294
BACnet Serial Communication .......................................... 288
BACnet Setup Parameters ................................................ 288
BACnet Specifications .................................................... 285
Baseblock Command (N.O., N.C.) ........................................76
Base Frequency ..............................................................67
Base Voltage .................................................................67
BAS Interlock ................................................................84
BAS Interlock Relay Contact ..............................................93
Bi-Directional Speed Search Selection ...................................36
Binary Input Objects ...................................................... 298
Binary Output Objects .................................................... 298
Binary Value Objects...................................................... 298
BP Auto Transfer on Fault Enable ................................ 151, 259
BP BAS Interlock............................................................83
BP BAS Interlock Relay ....................................................93
BP Bypass Relay.............................................................93
BP Bypass Run...............................................................84
BP Customer Safeties .......................................................83
BP Drive/Bypass Select.....................................................83
BP Drive Relay...............................................................93
BP Emergency Override ....................................................83
BP Energy Save Bypass Speed Increase.......................... 152, 259
BP Energy Save Bypass Timer .................................... 152, 259
BP Energy Save Bypass Trigger Level ........................... 151, 259
Broadcast Messages ....................................................... 363
bUS Error Auto Reset .......................................................73
Bypass Operation .......................................................... 146
C
Capacitor Maintenance.................................................... 267
Capacitor Maintenance Setting .................................... 135, 254
Carrier Frequency Lower Limit............................................55
Carrier Frequency Proportional Gain .....................................55
Carrier Frequency Reduction............................................. 248
Carrier Frequency Reduction Off-Delay Time ........................ 124
Carrier Frequency Reduction Off Delay Time......................... 248
Carrier Frequency Reduction Rate during oH Pre-Alarm ............ 124
Carrier Frequency Reduction Selection................................. 123
Carrier Frequency Reduction Selection during oH Pre-Alarm ...... 249
Carrier Frequency Selection................................................55
Carrier Frequency Upper Limit ............................................55
CE Detection Time ............................................ 290, 328, 347
Command Messages from Master to Drive ................ 293, 333, 349
Communication Errors .................................................... 301
Communication Fault Detection Selection ................. 289, 327, 346
Communication Option Card Reference................................ 268
Communication Parity Selection ............................ 288, 326, 345
Communications Enter Function Selection ................ 290, 328, 347
Communications Error Operation Selection .............................72
Communication Speed Selection ............................ 288, 326, 345
Communications Protocol Selection ........................ 289, 327, 346
Communications Timing ..................................... 293, 333, 349
Communication Test Mode.................................................82
Connecting to a BACnet Network....................................... 286
Connecting to an N2 Network ........................................... 324
Connection of a Motor PTC .............................................. 103
Continuous Electrothermal Operation Selection ................ 104, 243
Inde
Advertisement
Table of Contents
