Table of Contents
Advertisement
Overexcitation Deceleration Gain ...................................... 127, 250
Overexcitation Operation Selection .................................... 127, 250
Overheat Alarm Level......................................................91, 247
Overheat Pre-Alarm Operation Selection ...............................92, 247
Overtorque Detection Operation.............................................. 117
Overvoltage Suppression Function ........................................... 110
Overvoltage Suppression Function Selection ............................... 110
ov Suppression Function Selection........................................... 245
P
Password and Password Setting ................................................20
Peak Hold Current .............................................................. 267
Peak Hold Output Frequency ................................................. 267
Performance Life ............................................................... 168
Performance Life Monitors Maintenance Monitors........................ 168
Periodic Inspection ............................................................. 166
Periodic Maintenance .......................................................... 168
Phase Order Selection ............................................................28
Phase Order Selection (Emergency Override Reference Selection) .......84
Phase Order Selection (Emergency Override Speed) ........................84
PI2 Disable (N.O.) ................................................................83
PI2 Integral Hold..................................................................84
PI2 Integral Reset .................................................................83
PI2 Inverse Operation ............................................................83
PI Accel/Decel Time .............................................................45
PID Feedback High...............................................................92
PID Feedback Low ...............................................................92
PI Disable ..........................................................................79
PI Feedback...................................................................... 268
PI Feedback Function Selection ................................................47
PI Feedback High Detection Level .............................................44
PI Feedback High Detection Time .............................................44
PI Feedback Loss Detection Selection .........................................43
PI Feedback Low Detection Level .............................................44
PI Feedback Low Detection Time ..............................................44
PI Feedback Offset ...............................................................47
PI Function Setting ...............................................................41
PI Input (feedback) ............................................................. 268
PI Input Level Selection .........................................................80
PI Input Limit .....................................................................47
PI Integral Hold ...................................................................80
PI Integral Reset ............................................................. 80, 83
PI Maximum Boost Time........................................................47
PI Monitors ...................................................................... 160
PI Offset Adjustment .............................................................41
PI Output......................................................................... 268
PI Output 2 Monitor Max Upper/Lower 4 Digits ............................49
PI Output Gain Setting ...........................................................42
PI Output Level Selection .......................................................42
PI Output Limit ...................................................................41
PI Output Lower Limit...........................................................47
PI Output Monitor Calculation Method........................................48
PI Output Reverse Selection ....................................................42
PI Primary Delay Time Constant ...............................................41
PI Setpoint ....................................................................... 268
PI Setpoint Boost Setting ........................................................46
PI Setpoint Display Digits .......................................................48
PI Setpoint Monitor Unit Selection.............................................49
PI Setpoint Scaling ...............................................................46
PI Setpoint Selection .............................................................45
PI Setpoint User Display.........................................................48
PI Setpoint Value .................................................................45
PI Sleep Delay Time .............................................................45
PI Sleep Function Start Level ...................................................45
PI Sleep Input Source ............................................................46
PI Snooze Deactivation Level...................................................46
PI Snooze Delay Time ...........................................................46
PI Snooze Feedback Level ......................................................47
PI Snooze Level...................................................................46
PI Soft Starter Cancel ............................................................80
PI Square Root Gain..............................................................47
PI Unit Selection ..................................................................48
PM Motor Auto-Tuning Mode Selection .................................... 157
PM Motor Base Frequency .................................................... 158
PM Motor Control Tuning..................................................... 127
PM Motor d-Axis Inductance ................................................. 158
PM Motor Induced Voltage Constant ........................................ 158
PM Motor q-Axis Inductance ................................................. 158
PM Motor Rated Current ...................................................... 158
PM Motor Rated Power........................................................ 157
PM Motor Rated Voltage ...................................................... 157
PM Motor Stator Resistance .................................................. 158
PM Motor Type ................................................................. 157
Power Detection Filter Time ....................................................51
Present Value Access........................................................... 294
Previous Fault ................................................................... 264
Program Lockout .................................................................79
Programmable Bypass Logic.................................................. 146
Programmable Run Timers for Real Time Clock (RTC).................. 138
Proportional Gain Setting (P) ...................................................41
Pull-In Current ............................................................ 128, 251
Pull-In Current Compensation Time Constant.............................. 251
Pull-In Current Level for PM Motor Tuning................................ 159
R
READ ............................................................................ 134
Reading BACnet Drive Parameters .......................................... 300
Reading Drive MEMOBUS/Modbus Register Contents .................. 352
Real Time Clock ................................................................ 138
Real Time Clock Setting....................................................... 136
Reference Sample Hold ..........................................................79
Relay Operator Control ..........................................................93
Removing the Cooling Fan .................................................... 174
Replacement Parts .............................................................. 168
Reset Communication Parameters..............................................73
Response Messages from Drive to Master ...................... 293, 333, 349
Restart Enabled ...................................................................91
Reverse Jog ........................................................................78
Reverse Operation Selection ....................................................28
Reverse Operation Selection 2 by PI Output..................................49
Reverse Run Command for 2-Wire Seq. ......................................80
RS-422 Interface ................................................................ 344
RS-485 Interface .............................................. 287, 309, 325, 343
RTS Control Selection ............................................. 289, 327, 346
Run Command at Power Up.....................................................29
Run Command for 2-Wire Seq. 2...............................................80
Run Command Method Selection ................................ 290, 328, 347
RUN Command Selection for AUTO mode ................................ 215
Run Command Selection for AUTO Mode ...................................25
Run Command Selection in Programming Mode ............................28
Inde
7
Advertisement
Table of Contents
