YASKAWA CIMR-ZU A Series Programming Manual page 372

Inde
Metasys N2 Point Database ................................................... 334
Metasys N2 Specifications .................................................... 322
Middle Output Frequency .......................................................67
Middle Output Frequency 2 .....................................................67
Middle Output Frequency Voltage .............................................67
Middle Output Frequency Voltage 2 ...........................................67
Minimum Current Detection Level during Speed Search ...................35
Minimum KEB Time........................................................... 106
Minimum Output Frequency ....................................................67
Minimum Output Frequency Voltage..........................................67
Minimum Wait Time for Sending Messages.................... 293, 333, 349
Momentary Power Loss Minimum Baseblock Time................. 105, 244
Momentary Power Loss Operation Selection ...........................34, 244
Momentary Power Loss Ride-Thru .......................................... 104
Momentary Power Loss Ride-Thru Time ............................. 105, 244
Momentary Power Loss Voltage Recovery Ramp Time ............ 105, 244
Monitor Parameters.........................................................98, 263
Most Recent Fault .............................................................. 265
Motor Acceleration Time for Inertia Calculations ................... 111, 245
Motor Base Frequency ................................................... 156, 261
Motor Base Speed ........................................................ 157, 261
Motor d-Axis Current at Previous Fault ..................................... 265
Motor d-Axis Inductance ........................................................71
Motor Direction at Power Up when Using Operator................. 134, 253
Motor Excitation Current (ld) ................................................. 269
Motor Induction Voltage Constant 1 ...........................................71
Motor Induction Voltage Constant 2 ...........................................71
Motor Iron Loss ........................................................... 157, 261
Motor Iron Loss for Torque Compensation ...................................69
Motor Line-to-Line Resistance .................................................69
Motor No-Load Current..........................................................69
Motor Overheat Alarm Operation Selection .......................... 103, 243
Motor Overheat Fault Operation Selection............................ 103, 243
Motor Overload Alarm...........................................................91
Motor Overload Estimate (oL1) .............................................. 267
Motor Overload Protection Selection ....................................91, 243
Motor Overload Protection Time ....................................... 102, 243
Motor Pre-Heat 1 .................................................................81
Motor Pre-Heat 2 .................................................................81
Motor Pre-Heat Current 2 .......................................................30
Motor Protection ................................................................ 101
Motor Protection Using a PTC Thermistor.................................. 102
Motor PTC Characteristics .................................................... 103
Motor q-Axis Current at Previous Fault ..................................... 265
Motor q-Axis Inductance ........................................................71
Motor Rated Current ............................................ 68, 70, 156, 261
Motor Rated Power .............................................. 69, 70, 156, 261
Motor Rated Slip..................................................................68
Motor Rated Voltage ..................................................... 156, 261
Motor Secondary Current (Iq) ................................................ 269
Motor Stator Resistance..........................................................70
Motor Temperature Input Filter Time.................................. 104, 243
Motor Underload Protection Level at Minimum Frequency ........ 119, 247
Motor Underload Protection Selection................................. 118, 247
Multi-Function Analog Inputs ..................................................94
Multi-Function Analog Input Terminal Settings .............................94
Multi-Function Analog Outputs ................................................98
Multi-Function Analog Output Terminal AM Bias ..........................99
Multi-Function Analog Output Terminal AM Gain..........................99
Multi-Function Analog Output Terminal AM Monitor Selection..........99
72
Multi-Function Analog Output Terminal AM Signal Level Selection .. 100
Multi-Function Analog Output Terminal FM Bias...........................99
Multi-Function Analog Output Terminal FM Gain ..........................99
Multi-Function Analog Output Terminal FM Monitor Selection ..........99
Multi-Function Analog Output Terminal FM Signal Level Selection... 100
Multi-Function Digital Inputs ...................................................74
Multi-Function Digital Outputs .................................................84
Multi-Step Speed Reference.....................................................75
N
N2 Serial Communication ..................................................... 326
N2 Setup Parameters ........................................................... 326
N2 Specifications ............................................................... 323
NetRef/ComRef Function Selection............................................73
Network Termination ........................................ 286, 309, 325, 344
Number of Auto Restart Attempts...................................... 114, 246
Number of Motor Poles ......................................... 69, 70, 156, 261
Number of PM Motor Poles ................................................... 158
Number of Run Commands ................................................... 267
Number of Run Commands Counter Initialization................... 136, 254
Number of Speed Search Restarts ..............................................36
O
OFF Key Function Selection .................................................. 253
Offset Frequencies........................................................... 63, 81
Offset Frequency................................................................ 269
oH Pre-Alarm Time Limit .......................................................92
oL1 Current Level .............................................................. 243
oL2 Characteristics Selection at Low Speeds......................... 122, 248
oPE Fault Parameter............................................................ 264
Operation Selection when HOA Keypad is Disconnected .......... 134, 253
Operation Status Monitors..................................................... 160
Operator Related Settings...................................................... 130
Option Frequency Reference .................................................. 268
Option Monitors 1 to 20 ....................................................... 270
Output Current .................................................................. 263
Output Current 1 during Speed Search ........................................35
Output Current 2 During Speed Search (Speed Estimation Type) .........35
Output Current at Previous Fault ............................................. 265
Output Frequency............................................................... 263
Output Frequency after Soft Start ............................................ 264
Output Frequency at Previous Fault.......................................... 265
Output Frequency Reduction During Overheat Alarm .................... 120
Output Ground Fault Detection Selection ............................. 121, 248
Output Phase Loss Detection Level for Dynamic Audible Noise Control ... 260
Output Phase Loss Detection Lvl for Dynamic Noise Control ........... 155
Output Phase Loss Protection ................................................. 248
Output Phase Loss Protection Selection ..................................... 121
Output Power.................................................................... 263
Output Power at Previous Fault............................................... 265
Output Terminal Status ........................................................ 263
Output Terminal Status at Previous Fault ................................... 265
Output Voltage at Previous Fault ............................................. 265
Output Voltage Limit........................................................... 129
Output Voltage Reference ..................................................... 263
Output Voltage Reference (Vd)............................................... 269
Output Voltage Reference (Vq)............................................... 269
ov2 Detect Time .......................................................... 155, 260
Overcurrent Detection Gain ............................................. 122, 248
Overexcitation Deceleration................................................... 109