YASKAWA CIMR-ZU A Series Programming Manual page 220

A b Application
No
(Addr Name
e )
b5-39 PI Setpoint Display
(1FF) Digits
Frequency Reference
b5-40
Monitor Content during
(17F)
PI
b5-41
PI Unit Selection
(160)
b5-42
PI Output Monitor
(161)
Calculation Method
b5-43
PI Output 2 Monitor
(162)
Max Upper 4 Digits
b5-44
PI Output 2 Monitor
(163)
Max Lower 4 Digits
b5-45
PI Output 2 Monitor
(164)
Minimum
b5-46 PI Setpoint Monitor Unit
(165) Selection
b5-47 Reverse Operation
(17D) Selection 2 by PI Output
<1> Default setting is determined by parameter A1-02, Control Method Selection.
<2> Internally limited to the value of b5-38 in drive software versions PRG: 1014 and later. Changing b5-20, b5-38, and b5-39 will not automatically
update the value of this parameter.
<3> Default setting is dependent on parameter b5-20, PI Setpoint Scaling.
22
LCD Display
PI UsrDspDigits 0: No decimal places
0: No Dec (XXXXX) 1: One decimal place
1: 1 Dec (XXXX.X) 2: Two decimal places
2: 2 Dec (XXX.XX) 3: Three decimal places
3: 3 Dec (XX.XXX)
0: Display the frequency reference (U1-01) after PI
Fref Mon Sel@PI
compensation has been added.
0: Fref Mon w PI
1: Display the frequency reference (U1-01) before PI
1: Fref Mon w/o PI
compensation has been added.
PI Mon Unit Sel
0: WC (Inch of water)
0: WC
1: PSI (Pounds per square inch)
1: PSI
2: GPM (Gallons per minute)
2: GPM
3: F (Degrees Fahrenheit)
3: °F
4: CFM (Cubic feet per minute)
4: CFM
5: CMH (Cubic meters per hour)
5: CMH
6: LPH (Liters per hour)
6: LPH
7: LPS (Liters per second)
7: LPS
8: Bar (Bar)
8: Bar
9: Pa (Pascal)
9: Pa
10: C (Degrees Celsius)
10: °C
11: Mtr (Meters)
11: Mtr
12: Ft (Feet)
12: Ft
13: LPM (Liters per minute)
13: LPM
14: CMM (Cubic meters per minute)
14: CMM
PI Out Calc Mode
0: Linear - the monitor displays PI output
0: Linear
1: Square root - the monitor displays square root PI output
1: Square root
2: Quadratic - the monitor displays 1/(PI output)
2: 1/f2
3: Cubic - the monitor displays 1/(PI output)
3: 1/f3
Sets the upper 4 digits of the maximum monitor value.
Used with b5-44 to set maximum monitor value of U5-14 and
PI Out MonMax U4
U5-15 at maximum frequency.
Note:
Sets the lower 4 digits of the maximum monitor value.
Used with b5-43 to set maximum monitor value of U5-14 and
PI Out MonMax L4
U5-15 at maximum frequency.
Note:
Sets the minimum display value at zero speed.
This function is effective when b5-42 is set to 0 (Linear output
PI Out MonMin
mode).
Note:
PI Mon Unit Sel
0: WC (Inch of water)
0: WC
1: PSI (Pounds per square inch)
1: PSI
2: GPM (Gallons per minute)
2: GPM
3: F (Degrees Fahrenheit)
3: °F
4: CFM (Cubic feet per minute)
4: CFM
5: CMH (Cubic meters per hour)
5: CMH
6: LPH (Liters per hour)
6: LPH
7: LPS (Liters per second)
7: LPS
8: Bar (Bar)
8: Bar
9: Pa (Pascal)
9: Pa
10: C (Degrees Celsius)
10: °C
11: Mtr (Meters)
11: Mtr
12: Ft (Feet)
12: Ft
13: LPM (Liters per minute)
13: LPM
14: CMM (Cubic meters per minute)
14: CMM
Output Rev Sel2 Reverse operation selection when b5-01 = 3
0: 0 limit 0: Reverse Disabled
1: Reverse 1: Reverse Enabled
Description
Used for U5-14 and U5-15 only.
Used for U5-14 and U5-15 only.
Used for U5-14 and U5-15 only.
alues Pa e
Default: <3>
48
Range: 0 to 3
Default: 0
48
Range: 0, 1
Default: 0
48
Range: 0 to 14
Default: 0
48
Range: 0 to 3
Default: 0
Min.: 0
49
Max.: 9999
Default: 0
Min.: 0
49
Max.: 99.99
Default: 0
Min.: 0
49
Max.: 999.9
Default: 0
49
Range: 0 to 14
Default: 1
49
Range: 0, 1