Table of Contents
Advertisement
Inde
Control Method Selection .......................................................18
Control Mode.................................................................... 263
Control Mode Dependent Parameter Default Values ...................... 271
Cooling Fan Maintenance ..................................................... 267
Cooling Fan Maintenance Setting (Operation Time) ...................... 254
Cooling Fan Operation Time.................................................. 267
Cooling Fan Operation Time Setting......................................... 135
Cooling Fan Replacement ..................................................... 174
Copy Allowed Selection ....................................................... 135
Copy Function................................................................... 134
Copy Function Selection....................................................... 134
CRC-16 .......................................................................... 350
CRC-16 Checksum Calculation Example ................................... 351
Cumulative Operation Time................................................... 267
Cumulative Operation Time at 5th Most Recent Fault .................... 266
Cumulative Operation Time at Most Recent Fault ......................... 265
Cumulative Operation Time at Previous Fault.............................. 265
Cumulative Operation Time Selection................................. 135, 254
Cumulative Operation Time Setting ................................... 135, 254
Current Control Gain during Speed Search (Speed Estimation Type).....35
Current Control Integral Time during Speed Search (Speed Estimation
Type) ...............................................................................35
Current Fault .................................................................... 264
Current Unbalance Detection (LF2).................................... 122, 248
Customer Safeties.................................................................84
Cyclic Redundancy Check..................................................... 350
D
Daily Inspection................................................................. 165
d-Axis Current for High Efficiency Control ................................ 128
DC Bus Pre-Charge Relay Maintenance Setting ........................... 135
DC Bus Undervoltage ............................................................88
DC Bus Voltage................................................................. 263
DC Bus Voltage Adjustment Gain ..................................... 111, 245
DC Bus Voltage at Previous Fault............................................ 265
DC Bus Voltage Setpoint during KEB....................................... 106
DC Injection Braking Current...................................................30
DC Injection Braking Start Frequency.........................................29
DC Injection Braking Time at Start ............................................30
DC Injection Braking Time at Stop ............................................30
Deceleration Rate Calculation Gain.......................................... 245
Deceleration Time ................................................................52
Deceleration Time at Stall Prevention during Acceleration......... 107, 245
Defaults by Drive Model Selection........................................... 133
Desired DC Bus Voltage during KEB ....................................... 244
Device Object ................................................................... 299
Digital Outputs ....................................................................84
Direction Command for 2-Wire Seq. 2 ........................................80
Drive/kVA Selection ........................................................... 253
Drive Cooling Fans ............................................................. 166
Drive Delay Time Setting .......................................................28
Drive Enable.................................................................. 82, 92
Drive Enable2 .....................................................................83
Drive Model Selection ......................................................... 133
Drive Mode Unit Monitor Selection ......................................... 130
Drive Operations by BACnet ................................................. 292
Drive Operations by N2........................................................ 330
Drive Operation Status at Previous Fault.................................... 265
Drive Overheat Alarm............................................................92
Drive Overheat Alarm (oH2)....................................................76
7
Drive Overheat Pre-Alarm.......................................................91
Drive Ready .......................................................................87
Drive Slave Address................................................ 288, 326, 345
Drive Status...................................................................... 264
Drive Transmit Wait Time ........................................ 289, 327, 346
During Baseblock.................................................................91
During Baseblock (N.O.) ........................................................88
During Fast Stop ..................................................................92
During Frequency Output........................................................91
During KEB Operation...........................................................92
During Run ........................................................................85
During Short Circuit Braking ...................................................92
During Speed Search .............................................................92
Dynamic Audible Noise Control Function Selection ...................... 255
Dynamic Audible Noise Control Selection.................................. 137
Dynamic Noise Control Function ............................................ 137
E
Emergency Override ........................................................... 147
Emergency Override Forward Run.............................................84
Emergency Override Reference Selection................................... 260
Emergency Override Reverse Run .............................................84
Emergency Override Speed ................................................... 260
Enabling Programmable Bypass Logic ...................................... 146
Energy Saving Coefficient Value...............................................51
Energy Saving Control Selection ...............................................50
Energy Savings Mode .......................................................... 150
Enter Command........................................................... 290, 366
Enter command necessary ......................................... 290, 328, 347
Enter command not necessary .................................... 290, 328, 347
Enter Command Types................................................... 300, 366
External Fault .....................................................................79
External Fault from Comm. Option Detection Selection....................72
External Fault from Comm. Option Operation Selection ...................72
External Speed Search Command ..............................................81
F
F1/F2 Key Function Selection ................................................ 132
Fast Stop (N.O., N.C.) ...........................................................78
Fast Stop Time ....................................................................53
Fault History..................................................................... 160
Fault Reset .........................................................................78
Fault Reset Command Active ...................................................89
Fault Reset Interval Time................................................ 116, 246
Fault Reset Operation Selection ........................................ 116, 247
Fault Restart .......................................................................91
Fault Trace....................................................................... 160
Field Weakening ..................................................................81
Field Weakening Frequency Limit .............................................62
Field Weakening Level ..........................................................62
Forward Jog .......................................................................78
Forward Run Command for 2-Wire Seq. ......................................80
Frequency Detection 1 ...........................................................86
Frequency Detection 2 ...........................................................87
Frequency Detection 3 ...........................................................90
Frequency Detection 4 ...........................................................90
Frequency Gain at KEB Start ................................................. 106
Frequency Reduction Rate during Overheat Pre-Alarm............. 120, 248
Frequency Reference .......................................................58, 263
Frequency Reference at Previous Fault ...................................... 265
Advertisement
Table of Contents
