YASKAWA CIMR-ZU A Series Programming Manual page 371

Frequency Reference at Reference Loss............................... 113, 246
Frequency Reference from MEMOBUS/Modbus Comm. ................ 268
Frequency Reference Hold Function Selection ...............................61
Frequency Reference Loss.......................................................88
Frequency Reference Loss Detection Selection ........................88, 246
Frequency Reference Lower Limit .............................................59
Frequency Reference Monitor Content During PI ...........................48
Frequency Reference Monitor Custom Units 1 to 3 ....................... 132
Frequency Reference Selection for AUTO Mode ............................24
Frequency Reference Selection for AUTO mode .......................... 215
Frequency Reference Setting Method Selection...................... 133, 253
Frequency Reference Source ....................................................88
Frequency Reference Source Selection ...................................... 268
Frequency Reference Upper Limit .............................................59
Frequency Related Monitor Custom Units 1 to 3 .......................... 132
Function Code................................................................... 350
G
GF1 Error ..........................................................................81
H
H1 Multi-Function Digital Input Selections................................. 233
H3 Multi-Function Analog Input Settings................................... 240
HAND/AUTO During Run Selection.................................. 152, 259
HAND Frequency Reference 1 ......................................... 154, 259
HAND Frequency Reference Selection................................ 152, 259
HAND Key Function Selection (HOA Keypad) ..................... 154, 260
HAND Mode Behavior Selection ...................................... 152, 259
HAND Mode PI Selection............................................... 152, 259
HAND Mode Select ..............................................................82
Heatsink Cooling Fan Off-Delay Time ...................................... 121
Heatsink Cooling Fan Operation Delay Time .............................. 248
Heatsink Cooling Fan Operation Selection............................ 121, 248
Heatsink Temperature.......................................................... 267
High Current Alarm Selection .......................................... 124, 248
High Slip Braking ..........................................................82, 126
High Slip Braking Current Limit ............................................. 126
High-Slip Braking Current Limit ............................................. 250
High Slip Braking Deceleration Frequency Width......................... 126
High-Slip Braking Deceleration Frequency Width......................... 250
High Slip Braking Dwell Time at Stop ...................................... 126
High-Slip Braking Dwell Time at Stop ...................................... 250
High Slip Braking Overload Time............................................ 126
High-Slip Braking Overload Time ........................................... 250
High Slip Suppression Current Level ........................................ 127
High-Slip Suppression Current Level........................................ 250
HOA Keypad Display Selection .............................................. 130
HOA Keypad Functions ....................................................... 133
Hunting Prevention ............................................................. 125
Hunting Prevention Gain Setting ....................................... 125, 250
Hunting Prevention Gain while in Reverse ........................... 125, 250
Hunting Prevention Selection ........................................... 125, 250
Hunting Prevention Time Constant .................................... 125, 250
I
Immediate Transfer to Bypass ................................................ 146
Induced Voltage Constant Unit Selection ................................... 158
Initialize Parameters..............................................................19
Input Phase Detection Level .................................................. 248
Input Phase Loss Detection Level ............................................ 121
Input Phase Loss Protection Selection ................................. 120, 247
Input Terminal Status .......................................................... 263
Input Terminal Status at Previous Fault ..................................... 265
Input Voltage Setting.............................................................64
Inrush Prevention Relay Maintenance Setting .............................. 254
Inspection .................................................................. 165, 166
Installation Method Selection ........................................... 123, 248
Installing the Cooling Fan ..................................................... 176
Integral Limit Setting.............................................................41
Integral Time Setting (I) .........................................................41
Internal Cooling Fan Alarm .....................................................93
J
Jog 2 ................................................................................82
Jog Frequency Reference ........................................................58
Jog Reference Selection..........................................................75
Jump Frequency...................................................................60
Jump Frequency Width ..........................................................60
K
KEB Acceleration Time ................................................. 105, 244
KEB Deceleration Time ................................................. 105, 244
KEB Detection Time ........................................................... 106
KEB Method Selection......................................................... 106
KEB Ride-Thru 1 .................................................................82
KEB Ride-Thru 2 .................................................................83
KEB Start Output Frequency Reduction..................................... 244
kWh............................................................................... 267
kWh, Lower 4 Digits ........................................................... 267
kWh, Upper 5 Digits ........................................................... 267
kWh Monitor Initialization .................................................... 136
kWh Monitor Initial Value Selection ........................................ 254
L
Language Selection...............................................................18
LED Check ...................................................................... 267
Load Current .................................................................... 251
Load Inertia................................................................ 129, 251
Load Inertia Ratio......................................................... 112, 245
Loopback Test................................................................... 352
Loss of Reference Function ................................................... 113
M
Main Contactor and Cooling Fan Power Supply Failure ............ 155, 260
Main Contactor and Cooling Fan Power Supply Failure Selection ...... 248
Maintenance ............................................................... 168, 169
Maintenance Alarms ........................................................... 169
Maintenance Monitors ......................................................... 160
Maintenance Monitor Settings ................................................ 135
Maintenance Period ..............................................................91
Master Speed Reference Lower Limit .........................................60
Maximum Output Frequency....................................................67
Maximum Voltage................................................................67
MEMOBUS/Modbus Communications Reference......................... 268
MEMOBUS/Modbus Data Table............................................. 354
MEMOBUS/Modbus Error Code ............................................ 264
MEMOBUS/Modbus Error Codes ........................................... 367
MEMOBUS/Modbus Setup Parameters ..................................... 345
MEMOBUS/Modbus Specifications ......................................... 341
Message Format................................................................. 350
Message ID (INV) .............................................................. 264
Message ID (OPR).............................................................. 264
Inde
71