Renesas M16C/6NK Hardware Manual page 32

Under development
This document is under development and its contents are subject to change.
M16C/6N Group (M16C/6NK, M16C/6NM)
Table 1.10 Pin Description (100-pin and 128-pin Versions) (2)
Signal Name Pin Name
Main clock XIN
input
Main clock XOUT
output
Sub clock XCIN
input
Sub clock XCOUT
output
(3)
BCLK output BCLK
Clock output CLKOUT
INT interrupt input NT0 to INT8
_______ ________
NMI interrupt
NMI
input
______
Key input KI0 to KI3
interrupt input
Timer A TA0OUT to TA4OUT
TA0IN to TA4IN
ZP
Timer B TB0IN to TB5IN
___
Three-phase motor U, U, V, V, W, W
control output
__________
Serial interface
CTS0 to CTS2
__________
RTS0 to RTS2
CLK0 to CLK6
RXD0 to RXD2
SIN3 to SIN6
TXD0 to TXD2
SOUT3 to SOUT6
CLKS1
2
I C mode SDA0 to SDA2
SCL0 to SCL2
Reference
VREF
voltage input
A/D converter
AN0 to AN7
AN0_0 to AN0_7
AN2_0 to AN2_7
_____________
ADTRG
ANEX0
ANEX1
D/A converter
DA0, DA1
CAN module
CRX0, CRX1
CTX0, CTX1
I: Input O: Output
NOTES:
1. Ask the oscillator maker the oscillation characteristic.
________ ________
2. INT6 to INT8, CLK5, CLK6, SIN5, SIN6, SOUT5, SOUT6 are only in the 128-pin version.
3. Not available the bus control pins in T/V-ver..
Rev.2.00 Nov 28, 2005
REJ09B0124-0200
I/O Type
I
O
I
O
O
O
(3)
I
I
______
I
I/O
I
I
I
___ ____
O
__________
I
__________
O
(3)
I/O
I
(3)
I
O
(3)
O
O
I/O
I/O
I
I
I
I/O
I
O
I
O
I/O: Input/Output
page 14 of 378
Description
I/O pins for the main clock oscillation circuit. Connect a ceramic
resonator or crystal oscillator between XIN and XOUT
To use the external clock, input the clock from XIN and leave
XOUT open.
I/O pins for a sub clock oscillation circuit. Connect a crystal
oscillator between XCIN and XCOUT
To use the external clock, input the clock from XCIN and leave
XCOUT open.
Outputs the BCLK signal.
The clock of the same cycle as fC, f8, or f32 is output.
______
Input pins for the INT interrupt.
_______
Input pin for the NMI interrupt.
Input pins for the key input interrupt.
These are timer A0 to timer A4 I/O pins.
These are timer A0 to timer A4 input pins.
Input pin for the Z-phase.
These are timer B0 to timer B5 input pins.
These are Three-phase motor control output pins.
These are send control input pins.
These are receive control output pins.
These are transfer clock I/O pins.
These are serial data input pins.
These are serial data input pins.
These are serial data output pins.
These are serial data output pins.
This is output pin for transfer clock output from multiple pins
function.
These are serial data I/O pins.
These are transfer clock I/O pins. (however, SCL2 for
the N-channel open drain output.)
Applies the reference voltage for the A/D converter and D/A
converter.
Analog input pins for the A/D converter.
This is an A/D trigger input pin.
This is the extended analog input pin for the A/D converter,
and is the output in external op-amp connection mode.
This is the extended analog input pin for the A/D converter.
These are the output pins for the D/A converter.
These are the input pins for the CAN module.
These are the output pins for the CAN module.
1. Overview
(1)
.
(1)
.