Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends. The larger the adjustment value, the narrower the bottom

margin of the image becomes.

16.6.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends. The larger the adjustment value, the narrower the bottom margin

of the image becomes.

16.6.14 <046: Horizontal scan end position correction (standard:scanning on ADF)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends. The larger the adjustment value, the narrower the

bottom margin of the image becomes.

16.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Correct the magnification of vertical scanning of a document fed from the ADF. The larger the adjustment value, the more the image stretches in the vertical scan-

ning direction.

16.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller the adjustment value, the more the image ruduces in the horizontal

scanning direction.

This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54

must also be incremented/decremented by the same amount.

Do not change the adjustment value extremely.

16.6.17 <054: Pickup motor speed correction (when the ADF is used) >

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

This menu is used to adjust the ADF pickup motor speed. If you have adjusted the ADF feed motor speed by selecting SCAN NUMERIC>48, the ADF pickup

motor speed must also be incremented/decremented by the same amount.

Do not change the adjustment value extremely.

16.6.18 <193: ADF special standard-sized paper: LGL misidentification-ready>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LEGAL").

0: LEGAL

1: FOOLSCAP

2: M_OFFICIO

3: A_FOOLSCAP

4: FOLIO

5: G_LEGAL

6: A_OFFICIO

7: B_OFFICIO

16.6.19 <194: ADF special standard-sized paper: LTR misidentification-ready>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").

0: LTR

1: G_LTR

2: A_LTR

16.6.20 <195: ADF special standard-sized paper: LTR_R misidentification-ready>

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").

0: LTR_R

1: FOOLSCAP

2: OFFICIO

3: E_OFFICIO

4: G_LTR_R

5: A_LTR_R

16.6.21 <213: XYZ correction value (X) of standard white plate> (equipped with SEND functions)

iR1020J / iR1024J / iR1020 / iR1024 / iR1024A / iR1024N / iR1024F / iR1024i / iR1024iF

If you replaced the image processor PCB, enter values indicated on the service label. If you have replaced the document glass, enter values indicated on the new

document glass and write the values on the service label.

16-24

0013-1367

0013-1369

0013-1370

0013-1371

0013-1372

0013-1373

0013-1374

0013-1375

0013-8781

Table of Contents