Test (Test Print Mode) - Canon ImageRunner iR8500 Series Service Manual

17.7 TEST (Test Print Mode)

17.7.1 COPIER
17.7.1.1 Copier List
iR105i/iR105+ / iR9070
<PG>
Sub-item
TYPE
TXPH
PG-PICK
2-SIDE
PG-QTY
<NETWORK>
Sub-item
PING
1) Press the switch at the operating section long for the shutdown sequence and turn the main power switch OFF.
2) Connect the network cable to this machine and turn the main power switch ON.
3) Notify the system administrator that the machine has been installed to request network setup.
4) Notify the system administrator of the network connection check plan and check the PING remote host address (IP address of a PC terminal in the user
network).
5) Select the service mode (COPIER>TEST>NETWORK>PING), enter the IP address checked at Step 4 from the ten-key pad of the operating section,
and press the OK key and the Start key.
- Once the network has been connected normally, OK is displayed. (End)
- If NG is displayed, check the connection of the network cable first. If the network cable is connected normally, do Step 6 and later. If the network
cable is not connected normally, repeat Step 5.
6) Select the service mode (COPIER>TEST>NETWORK>PING), enter the loopback address *(127.0.0.1), and press the OK key and the Start key.
- If NG is displayed, the TCP/IP setting of the local machine may be wrong. Return to Step 3 and check the setting again.
- If OK is displayed, the TCP/IP setting of the local machine seems correct but the network controller (main controller circuit board) may be faulty.
Check the controller at Step 7.
*: Since the loopback address signal is returned before the network controller, the TCP/IP setting of the local machine can be checked.
7) Select the service mode (COPIER>TEST>NETWORK>PING), enter the local host address (IP address of the local machine), and press the OK key.
COPIER>TEST>PG
Enter a test print type number and press the Start key for test printing. (After test
printing, be sure to return the number to 0.)
0: Image from CCD (Ordinary print)
1: Checker
2: 17 tones (Error diffusion method [T0BIC])
3: 17 tones (Dither screen method)
4: Totally white 00H
5: Halftone 80H (Error diffusion method [T0BIC])
6: Halftone 80H (Dither screen method)
7: Totally black FFH
8: Horizontal line (space: 27 dots, line width: 40 dots)
9: Horizontal line (space: 50 dots, line width: 60 dots)
10: Horizontal line (space: 3 dots, line width: 2 dots)
11: Halftone 60H (Error diffusion method [T0BIC])
12: Halftone 60H (Dither screen method)
13: Halftone 30H (Error diffusion method [T0BIC])
14: Halftone 30H (Dither screen method)
15 - 20: For development
Use it to switch between text mode and photo mode for test printing.
<Setting range>
0 to 4
Selecting an output stage for test printing
1: Cassette 1
2: Cassette 2
3: Cassette 3
4: Cassette 4
5: Side deck
6: Manual feed
7 - 8: Not used
Setting the output mode for test printing
0: Simplex [Default] 1: Duplex
Setting the number of pages for test printing
1 to 999 [Default: 1]
COPIER>TEST>NETWORK
Checking the connection from this machine to the network (TCP/IP only)
The network connection is checked when the machine has been installed and when the
connection has become faulty.
T-17-212
Description
T-17-213
Description
Chapter 17
0008-4962
Level
1
1
1
1
1
Level
1
17-209