Add Parameters To The Parameter List Displayed In Stop/Running State; Add Parameter To Common Parameter Setup List - Kruger Ecowatt K320 Series Operation Manual

Ecowatt Drive K320 series
®

5.4.3 Add parameters to the parameter list displayed in stop/running state

In the fourth-level menu of "State monitoring", the parameters in the list can be added to the
"parameter displayed in stop state" list or "parameter displayed in running state" list as shown
below.
16:02:35 Forward
Local Ready
P17.00：Setting frequency
P17.01：Output frequency
P17.02：Ramps reference frequency
P17.03：Output voltage
P17.04：Output current
P17.05：Motor speed
Return Add
16:02:35 16:02:35 16:02:35 16:02:35 Forward Forward Forward Forward
Local Local Local Local Ready Ready Ready Ready
P17.00: 设定频率 P17.00: 设定频率 P17.00: 设定频率
P17.00：Setting frequency
P17.01：Output frequency P17.01：输出频率 P17.01：输出频率 P17.01：输出频率
P17.02：斜坡给定频率 P17.02：斜坡给定频率 P17.02：Ramps reference frequency P17.02：斜坡给定频率
P17.03：输出电压 P17.03：Output voltage P17.03：输出电压 P17.03：输出电压
P17.04：输出电流 P17.04：输出电流 P17.04：Output current P17.04：输出电流
P17.05：电机转速 P17.05：电机转速 P17.05：电机转速 P17.05：Motor speed
返回 返回 返回 添加 添加 添加
Return Add
Press key to enter parameter addition interface, select the operation needed, and press
key, key or
included in the "parameter displayed in stop state" list or "parameter displayed in running
state" list, the parameter added will be at the end of the list; if the parameter is already in the
"parameter displayed in stop state" list or "parameter displayed in running state" list, the
addition operation will be invalid. If
addition peration in "Addition" interface, it will return to monitoring parameter list menu.
Part of the monitoring parameters in P07 HMI group can be added to the "parameter displayed
in stop state" list or "parameter displayed in running state" list; All the parameters in P17, P18
and P19 group can be added to the "parameter displayed in stop state" list or "parameter
displayed in running state" list.
Up to 16 monitoring parameters can be added to the "parameter displayed in stop state" list;
and up to 32 monitoring parameters can be added to the "parameter displayed in running
state" list.

5.4.4 Add parameter to common parameter setup list

In fourth-level menu of "parameter setup" menu, the parameter in the list can be added to the
"common parameter setup" list as shown below.
16:02:35
01: K320
Add to the parameter list displayed in stop state
Add to the parameter list displayed in running state
Return
Select
16:02:35 16:02:35 16:02:35 16:02:35
01: K320 01：GD350 01：GD350 01：GD350
添加到停机状态显示参数 添加到停机状态显示参数 添加到停机状态显示参数
Add to the parameter list displayed in stop state
添加到运行状态显示参数 添加到运行状态显示参数 添加到运行状态显示参数
Add to the parameter list displayed in running state
返回 返回 返回
选择 选择 选择 Return
Select
Figure 5-13 Add parameter diagram 1
key to confirm the addition operation. If this parameter is not
Forward
Local Ready 01: K320
Homepage
Confirm
Forward
Local Ready 01: K320 01：GD350 01：GD350 01：GD350
主页 主页 主页
Homepage 确定 确定 确定
Confirm
key or
-42-
Basic operation guidelines
16:02:35 Forward
Sure to add to the parameter list
displayed in stop state?
Return
16:02:35 16:02:35 16:02:35 16:02:35
Forward
Sure to add to the parameter list
确认添加到运行状态显示参数？ 确认添加到运行状态显示参数？ 确认添加到运行状态显示参数？
displayed in running state?
返回 返回 返回
Return Homepage
key is pressed without selecting
Local Ready 01: K320
Homepage Confirm
Local Ready 01：GD350 01：GD350 01：GD350 01: K320
主页 主页 主页
确定 确定 确定
Confirm