Table of Contents
Advertisement
Notify setting
Notify cost limit
notify the cost limit.
Alarm tone
......Selects the alarm tone from
the Melody folder. → P.266, 288
You can select "Clock Alarm Tone" in the Pre-
installed folder.
Select "OFF" to disable alarm tone.
......Sets the alarm tone volume with
Volume
c. "Adjusting the Ring Volume" → P.73
Set the respective items
3
N
The alarm volume while in original manner mode is the same
as that specified in "Phone vol." in "Original".
The
charges
for
i-mode
communication are not included in this function. To check
i-mode communication charges, see the "i-mode User's
Manual" you have received at the time of contract.
You can set the alarm mode by selecting "Operation
preferred" or "Alarm preferred" in "Alarm setting" (P.309).
● Alarm notification actions
After ending a call, the function notifies you with the
following methods when accumulated charges
exceed the cost limit.
■ When Notify cost limit is set to "ON" and
alarm tone is set to other than "OFF"
When the accumulated charge exceeds the
preset cost limit, the alarm starts sounding in
three seconds after you finish talking, and it lasts
about five minutes, while displaying the screen
notifying that the accumulated charge has
exceeded the limit. To stop the alarm tone, press
any key. After the notification, pressing
y
displays "
" (Call billing) desktop icon on
the standby screen.
■ When Notify cost limit is set to "ON" and
alarm tone is set to "OFF"
When the accumulated charge exceeds the
preset cost limit, "
" (Call billing) desktop icon is
displayed on the standby screen.
......Specifies whether to
o(Finish)
communication
and
packet
Ｓｅｔ−ｕｐ ｃｏｓｔ ｌｉｍｉｔ
ｉｓ ｅｘｃｅｅｄｅｄ
Ｃｏｓｔ ｌｉｍｉｔ
￥３０００
Ｄａｔｅ
１０／１９ １７：２２
t
or
● Checking details of "
The details of Notify cost limit is displayed by
selecting "
" (Call billing) desktop icon on the
standby screen.
1
On the standby screen
Select "
" (Call billing)
The alarm information of "Call
billing" is displayed.
Check the details
2
The standby screen reappears and "
disappears.
<Calculator>
Using the FOMA Terminal as
Calculator
You can use the FOMA terminal to perform 4
different types of arithmetical calculations (addition,
subtraction, multiplication and division).
● The number can be displayed up to 10 digits. Below
the decimal point, up to 9 digits can be displayed.
● If the result of a calculation exceeds 10 digits, ".E" is
displayed.
i85
Calculate
1
■ To calculate "23 + 57"
2
3
+
5
2 3 j 5 7 d
■ To use negative numbers in a calculation
To calculate using negative amounts, simply insert
−
"
" before the first digit.
− 2
3
+
5
h23j57d
N
t(
or
) can be used in the following cases.
・ After pressing ＋ , − , × , ÷ and ＝ ,
can start calculation from the beginning by pressing t.
・ While inputting numbers or decimal points,
displayed. You can delete wrong numbers or decimal
points by pressing t.
" (Call billing)
d
Ｃａｌｌ ｂｉｌｌｉｎｇ
Ｓｅｌｅｃｔ
d (OK)
" (Call billing)
7
=
Ｃａｌｃｕｌａｔｏｒ
=
･
The entered numbers
and calculation result
are displayed.
7
=
is displayed. You
is
315
Advertisement
Chapters
Table of Contents
