YASKAWA iQpump Micro CIMR-PW Series User Manual page 340

B.8 H Parameters: Multi-Function Terminals
H2-oo
Function
Setting
Frequency reference
9
source
A HAND mode
Torque detection 1
B
(N.O.)
Frequency reference
C
loss
D Braking resistor fault
E Fault
F Through mode
10 Minor fault
Fault reset command
11
active
12 Timer output
13 Speed agree 2
14 User-set speed agree 2
15 Frequency detection 3
16 Frequency detection 4
Torque detection 1
17
(N.C.)
Torque detection 2
18
(N.O.)
Torque detection 2
19
(N.C.)
1A During reverse
During baseblock
1B
(N.C.)
1E Restart enabled
Motor overload alarm
1F
(oL1)
Drive overheat pre-
20
alarm (oH)
Mechanical weakening
22
detection
2F Maintenance period
During frequency
37
output
38 Drive enabled
39 Watt hour pulse output Watt-hour Pulse
3D During speed search
3E PID feedback low
3F PID feedback high
4A During KEB Ride-Thru During KEB
4C During fast stop
4D oH Pre-alarm time limit OH Pre-Alarm
340
LCD Display
Open: External Reference 1 or 2 supplies the frequency reference
Ref Source (set in b1-01 or b1-15).
Closed: Digital operator supplies the frequency reference.
Open: External Reference 1 or 2 supplies the Run command (set in b1-02 or b1-16).
Hand Mode
Closed: Pump is in HAND Mode operation.
Closed: An overtorque or undertorque situation has been detected.
Trq Det 1 N.O.
Closed: Analog frequency reference has been lost.
Loss of Ref Frequency reference loss is detected when the frequency reference drops below
10% of the reference within 400 ms.
DB Overheat Closed: Braking resistor or transistor is overheated or faulted out.
Fault Closed: Fault occurred.
Not Used Set this value when using the terminal in the pass-through mode.
Closed: An alarm has been triggered, or the IGBTs have reached 90% of their
Minor Fault
expected life span.
Closed: A command has been entered to clear a fault via the input terminals or
Reset Cmd Active
from the serial network.
Timer Output Closed: Timer output.
Fref/Fout Agree2 Closed: When drive output frequency equals the frequency reference ±L4-04.
Fref/Set Agree 2 Closed: When the drive output frequency is equal to the value in L4-03 ±L4-04.
Closed: When the drive output frequency is less than or equal to the value in
Freq Detect 3
L4-03 ±L4-04.
Closed: When the output frequency is greater than or equal to the value in
Freq Detect 4
L4-03 ±L4-04.
Open: Overtorque or undertorque has been detected.
Trq Det 1 N.C.
Closed: Overtorque or undertorque has been detected.
Trq Det 2 N.O.
Open: Overtorque or undertorque has been detected.
Trq Det 2 N.C.
Reverse Dir Closed: Drive is running in the reverse direction.
Open: Drive has entered the baseblock state (no output voltage).
BaseBlk 2
Dur Flt Restart Closed: Automatic restart is performed
Closed: oL1 is at 90% of its trip point or greater. An oH3 situation also triggers
Overload (OL1)
this alarm.
Closed: Heatsink temperature exceeds the parameter L8-02 value.
OH Prealarm
Closed: Mechanical weakening detected.
MechFatigue(OL5)
Closed: Cooling fan, electrolytic capacitors, IGBTs, or the soft charge bypass relay
Maintenance
may require maintenance.
Open: Either the drive has stopped or baseblock, DC Injection Braking, or Initial
Excitation is being performed.
During RUN 2
Closed: Drive is running the motor (not in a baseblock state and DC Injection is
not being performed).
Drive Enable Closed: Multi-function input set for "Drive enable" is closed (H1-oo = 6A)
Output units are determined by H2-06. Outputs a pulse every 200 ms to indicate
the kWh count.
During SpdSrch Closed: Speed Search is being executed.
PID Feedback Low Closed: PID feedback level is too low.
PID FeedbackHigh Closed: The PID feedback level is too high.
Closed: KEB Ride-Thru is being performed.
Closed: A Fast Stop command has been entered from the operator or input
During Fast Stop
terminals.
Closed: oH pre-alarm time limit has passed.
Description
YASKAWA TOEP YAIQPM 03B YASKAWA AC Drive - iQpump Micro User Manual
Page
177
177
177
177
177
177
177
177
177
177
178
178
178
179
177
177
179
180
180
180
180
180
180
180
180
180
181
181
181
181
181
181