Since Pin7 of J3502 connector on the Color Sensor Driver PCB became loose, the connector had poor contact, ultimately causing the error code "E198-1000."

- E198-1000 can be displayed when a communication error occurs between the Color Sensor Driver PCB and the DC Controller PCB.

- The Color Sensor Driver PCB is used to detect the density of patch on image.

Field Remedy

1. Gently pull each wire of J3502 connector cable on the Color Sensor Driver PCB to check if there is a pin that becomes loose; if any, go to Step 2. If not,

go to Step 3.

2. Bring up the claw of the loosen pin slightly, and insert it to the connector; then check to make sure that the pin does not come off the connector.

3. Gently pull each wire of J1182 connector cable on the DC Controller PCB to check if there is a pin that becomes loose; if any, go to Step 4. If not, go to

Step 5.

4. Bring up the claw of the loosen pin slightly, and insert it to the connector; then check to make sure that the pin does not come off the connector.

5. If the symptom still occurs after Step 1 or Step 3, check the drawer connector cable of the fixing feeder assembly in the same manner as described above.

If a fault is found, modify it.

FM2-7733 Color Sensor Driver PCB Assembly

14.3.7.14 E202-0001/E202-0002/ Document exposure lamp's failure to light up occurs when mounting DADF-R1

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

After mounting the DADF-R1, either of the following symptoms occurred: document exposure lamp's failure in lighting up, E202-0001, or E202-0002.

- E202-0001 can be displayed when an error is found during the forward trip of the HP search. The possible cause of this error is a fault in the scanner motor

or the reader controller PCB.

- E202-0002 can be displayed when an error is found during the return trip of the HP search. The possible cause of this error is a fault in the scanner HP

sensor, scanner motor, or reader controller PCB.

Cause

Since the fan harness was pinched when mounting the cooling fan, the fuse on the interface PCB had an open-circuit.

Field Remedy

1. When the same symptom occurred after mounting the DADF-R1, check if the harness of the cooling is pinched.

2. If the cooling fan harness is pinched, suspect removal of harness covering and replace the fan and interface PCB with new ones (because the fuse may have

had an open-circuit).

FL2-3427 Front Fan

FL2-3426 Rear Fan

FM2-4662 Interface PCB Assembly

14.3.7.15 E225-0001 occurs with machine in which R-CON software Ver. 1.27 is installed

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Inspected by Canon Inc. ]

Description

A machine in which R-CON software Ver. 1.27 was installed sometimes caused the error code "E225-0001."

- E225-0001 can be displayed when the shading level is lower than the specified due to blowout of the lamp.

Cause

There was a difference in timing between the CCD output and detection.

Field Remedy

1. Check the version of the R-CON software; if it is earlier than Ver.4.02, upgrade the software to ver. 4.02 or later.

2. If the version of the software is earlier than Ver. 4.02, refit the flexible cable connecting the Reader Controller PCB to the Inverter PCB. Or clean the

terminals of the cable with lint-free paper moistened with alcohol, and then refit the terminals. Also, check the connection of the scanner lamp (Xenon lamp)

connector.

3. If the symptom still occurs, replace the CCD with a new one.

FM2-3920 CCD Unit

14.3.7.16 E604-1536 is displayed when connecting Secure Watermark-A1: This machine does not have sufficient image

memory

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

Since the error code "E604-1536" was displayed upon installation due to insufficient image memory, an image memory (option) was connected for solution.

- E604-1536 can be displayed when the image memory is faulty or lacking.

Field Remedy

When connecting the Secure Watermark-A1, Security Expansion Board-E1, and imageRUNNER Security Kit-A2, a memory of 512MB is required. When

connecting these items, connect an option memory (512MB DDR-SDRAM) to the connector at J1001 on the Main Controller PCB.

Note: If the Security Expansion Board-E1 or the imageRUNNER Security Kit-A2 is used together with the Color UFRII/PCL/PS Printer Kit-P1, it is not

necessary to connect the option memory. This is because it comes standard with the Color UFRII/PCL/PS Printer Kit-P1.

0529B002 imageRUNNER512MB Expansion RAM-C1 (Product)

14.3.7.17 E677-0080: Communication error occurs between this machine and imagePRESS Server- Q1

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

Since the error code "E677-0080" was indicated, the Reset key on the front side of the imagePRESS Server-Q1 was pressed to correct the error. In case that

the same symptom occurs, perform the following field remedy before pressing this Reset key.

- E667-0080 can be displayed when there is an error in the communication with the printer after the external controller has started up normally.

Chapter 14

0016-2920

0018-6306

0018-6304

0017-6706

0015-8160

14-41

Table of Contents