Canon imagePRESS C1 P Service Manual page 890

Code Type of Jam
0007 Delivery delay
0008 Delivery stationary 1
0009 Delivery stationary 2
0010 Pre-reverse delay 1
0011 Pre-reverse delay 2
0012 Pre-reverse delay 3
0013 Pre-reverse stationary 1
0014 Pre-reverse stationary 2
0015 Pre-reverse stationary 3
0016 Pre-reverse stationary 4
0017 Pre-reverse pickup delay
0018 Pre-reverse pickup stationary
1
0019 Pre-reverse pickup stationary
2
0020 Reverse pickup delay
0021 Reverse pickup stationary
0022 Pickup leading edge skew
0023 Pickup trailing edge skew
0024 Pickup NG 1
0025 Pickup NG 2
0026 Reverse pickup trailing edge
skew
0027 Reverse pickup NG 1
0030 Multifeeder registration
delay
0031 Multifeeder registration
stationary
0032 Multifeeder reverse
stationary
0033 Multifeeder delivery delay
0034 Multifeeder delivery
stationary
0043 1st sheet pickup stationary 1 S3
0044 1st sheet pickup stationary 2 S2
0045 1st sheet reverse delay
0046 1st sheet reverse stationary
0047 1st sheet delivery delay
0048 1st sheet delivery stationary
1
Sensor No. Details
PI13 When the delivery sensor fails to detect a document after it is fed by a specified amount (631mm - length
of document) after the startup of the belt motor during the delivery operation.
PI13,S9 When the multifeed registration roller sensor detects a document after it is fed by a specified amount
(length of document + 100mm) after the delivery sensor is turned ON during the delivery operation.
PI13,S9 When the delivery sensor detects a document after it is fed by a specified amount (100mm) after the
multifeed registration roller sensor is turned OFF during the delivery operation.
S3 When the registration rear roller sensor fails to detect a document after it is fed by a specified amount
(50mm) after the startup of the reverse motor during the pre-reverse operation.
S1,S3 When the reverse sensor fails to detect a document after it is fed by a specified amount (100mm) after
the registration roller rear sensor is turned ON during the pre-reverse operation.
PI4 When the pre-reverse sensor fails to detect a document when the reverse motor is stopped during the pre-
reverse operation.
S1,S4 When the separation sensor detects a document after it is fed by a specified amount (169mm) after the
reverse sensor is turned ON during the pre-reverse operation.
S2,S4 When the registration roller front sensor detects a document after it is fed by a specified amount
(120mm) after the trailing edge of the sheet comes out of the separation pullout roller during the pre-
reverse operation.
S2,S3 When the registration roller rear sensor detects a document after it is fed by a specified amount (50mm)
after the trailing edge of the sheet comes out of the registration roller front sensor during the pre-reverse
operation.
S1,S3 When the reverse sensor detects a document after it is fed by a specified amount (100mm) after the
trailing edge of the sheet comes out of the registration roller rear sensor during the pre-reverse operation.
S1 When the reverse sensor fails to detect a document after it is fed by a specified amount (100mm) after
the startup of the reverse motor during the pre-reverse pickup operation.
S1,PI4 When the pre-reverse sensor detects a document after it is fed by a specified amount after the reverse
sensor detects the leading edge of the sheet during the pre-reverse pickup operation.
S1,PI4 When the reverse sensor detects a document after it is fed by a specified amount after the pre-reverse
sensor detects the trailing edge of the sheet during the pre-reverse pickup operation.
S2 When the registration roller front sensor fails to detect a document after it is fed by a specified amount
(197mm) after the loop formation is completed during the reverse operation.
S2 When the registration roller front sensor detects a document after it is fed by a specified amount (length
of document x 1.5mm) after the registration roller front sensor is turned ON during the reverse operation.
S4,S5 When a difference in the leading edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the separation operation.
S4,S5 When a difference in the trailing edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the pickup operation.
S1 When the reverse sensor detects a document before it comes out of the registration roller front sensor
during the pickup operation.
S3,S2 When the registration roller rear sensor detects a document before the reverse motor is started during the
pickup operation.When the registration roller front sensor fails to detect a document after it is fed by a
certain amount during the pickup operation.When the registration roller rear sensor detects a document
before the reverse motor is started during the pre-reverse operation.When the registration roller front
sensor fails to detect a document when the trailing edge of the document passes through the reverse
sensor during the reverse operation.
S4,S5 When a difference in the trailing edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the pre-reverse operation.
PI4 When the pre-reverse sensor detects a document while the machine is waiting for the registration roller
front sensor to be turned ON during the reverse operation.
S9 When the multifeed registration roller sensor fails to detect a document after a specified period of time
(1 sec) passes after the startup of the delivery motor during the multifeed loop formation.
S1 When the reverse sensor fails to detect a document after it is fed by a specified amount (638mm) after
the startup of belt motor during the multifeed pickup operation.
S1 When the reverse sensor fails to detect a document after it is fed by a specified amount (50mm) after the
startup of the belt motor during the multifeed (platen roller) pickup operation.
PI13 When the delivery sensor fails to detect a document after it is fed by a specified amount (621mm - length
of document) during the multifeed delivery operation.
PI13 When the delivery sensor detects a document after it is fed by a specified amount (length of document x
1.5mm) after the delivery sensor is turned ON during the multifeed delivery operation.
When pickup stationary 1 (0003) occurs on the 1st sheet.
When pickup stationary 2 (0004) occurs on the 1st sheet.
S1 When reverse delay (0005) occurs on the 1st sheet.
S1 When reverse stationary (0006) occurs on the 1st sheet.
PI13 When delivery delay (0007) occurs on the 1st sheet.
PI13,S9 When delivery stationary 1 (0008) occurs on the 1st sheet.
Chapter 15
15-27