When the same symptom occurs, check to see if the tip of the screw fixing the decurler unit comes in contact with the pressure plate. The correct screw is a

binding screw (M4 x 8mm).

14.3.6 Jam (FIN)

14.3.6.1 179F Jam Code occurs when running saddle jobs with double-face glossy (coated) heavy paper and Saddle

Finisher-AA2 in use

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

Since a saddle job was performed using out-of-specification double-face glossy heavy paper, paper feed timing was delayed, and therefore the jam code

"179F" was displayed.

- 197F Jam Code can be displayed when the saddle assembly does not notice normal paper reception within approx. 10 sec after the stacker assembly has

noticed paper delivery to the saddle unit.

Cause

Since out-of-specification paper (double-face glossy heavy paper) was used, the stacker assembly failed to feed paper to the saddle assembly normally,

causing a delay of paper feed timing. This resulted in the jam.

Field Remedy

Check the type of used paper; if glossy heavy paper is used, replace it by in-specification plain paper (64 to 105g/square meters), and then make copies again.

Reference: Saddle control

In saddle jobs, the following steps are performed on every paper.

- Step1: The stacker assembly gives a paper transfer notice to the saddle assembly (using a signal).

- Step2: Paper is transferred from the stacker assembly to the saddle assembly.

- Step3: The saddle assembly gives a paper reception notice to the saddle assembly (using a signal).

14.3.6.2 179F Jam Code: J9 connector on Saddle Stitcher Controller PCB of Saddle Finisher-AA2 has poor contact

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

When the jam code "179F" occurs during a saddle job, perform the following field remedy.

- 179F Jam can be displayed when the saddle assembly does not notice normal delivery of paper within about 10 sec after the stacker assembly notices paper

transportation to the saddle assembly.

Field Remedy

1. Re-fit J9 connector of the Saddle Stitcher Controller PCB.

2. Check to see if the crescent roller phase sensor (PI12) comes off; if so, re-fit it. If it is mounted correctly, re-fit J126 connector.

3. Suspect that the crescent roller phase sensor fails to get in position because of rotation failure of the feed motor (M1), and re-fit J115 connector of the

motor; if the symptom is not solved, replace the motor.

WG8-5593 Photo-interrupter

4H3-0369 Stepping Motor

14.3.7 Error Code

14.3.7.1 E006-0002 occurs during standby: Fixing drawer connector has poor contact

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Case in the field ]

Description

In the field, the error code "E006-0002" was displayed. The cause of this error code seemed to be poor contact of the fixing drawer connector (the fixing

heater cable unit).

- E006-0002 can be displayed when the diconnection state of the fixing unit is detected for 0.6msc with the front cover closed.

Field Remedy

1. Check to see if the set lever of the fixing/feeder assembly is set correctly.

2. Re-fit all the connectors on the DC controller PCB.

3. If the symptom still occurs, check if the fixing drawer connector is soiled or deformed; if so, clean or modify it. Or replace it with a new one.

FM2-2620 Fixing Heater Cable Unit

14.3.7.2 E007/010E Jam Code/abnormal noise: Fixing upper unit mount is attached improperly

imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1+ (Printer) / imagePRESS C1+

[ Inspected by Canon Inc. ]

F-14-43

Chapter 14