Secondary Transfer Roller Brush (Lower) - Canon imagePRESS C1 P Service Manual

7.14.35 Secondary Transfer Roller Brush (Lower)

7.14.35.1 Preparation for Removing the Secondary
Transfer Roller Brush (Lower)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Pull out the fixing/feeding unit toward the front.
3) Remove the secondary transfer outside roller unit. (page 7-101)Refer-
ence [Removing the Secondary Transfer Outer Roller Unit]
4) Remove the secondary transfer outside roller sub-unit. (page 7-102)Ref-
erence [Removing the Secondary Transfer Outside Roller Sub-Unit]
5) Remove the secondary transfer outside roller. (page 7-104)Reference
[Removing the Secondary Transfer Outside Roller]
7.14.35.2 Removing the Secondary Transfer Roller Brush
(Lower)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the washer [1].
- 1 screw [2]
[1]
[2]
2) Remove the secondary transfer roller brush (lower) [1].
- 3 E-rings [2]
- 1 gear [3]
- 2 bearings [4]
[2]
[4]
[3]
[2]
7.14.36 ITB Bias Roller Cleaning Blade (Upper)
7.14.36.1 Preparation for Removing the ITB Bias Roller
Cleaning Blade (Upper)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Detach the process unit cover.
3) Lift the hopper unit.
4) Remove the primary charging assembly. (page 7-86)Reference [Re-
moving the Primary Corona Assembly]
5) Remove the pre-transfer charging assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Remove the drum unit. (page 7-89)Reference [Removing the Drum
Unit]
7) Pull out the fixing/feeding unit.
F-7-239
[1]
[2]
[4]
F-7-240
8) Remove the intermediate transfer unit. (page 7-100)Reference [Remov-
ing the Intermediate Transfer Unit]
9) Remove the ITB cleaning unit. (page 7-99)Reference [Removing the
ITB Cleaning Unit]
10) Remove the ITB cleaner brush (large). (page 7-105)Reference [Re-
0013-9771
moving the ITB Cleaner Brush (Large)]
7.14.36.2 Removing the ITB Bias Roller Cleaning Blade
(Upper)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the ITB bias roller [1].
- 1 gear [2]
- 1 screw [3]
- 1 contact cover [4]
0013-9772
2) Remove the ITB bias roller cleaning blade (upper) [1].
- 4 screws [2]
7.14.37 ITB Bias Roller Cleaning Blade (Lower)
7.14.37.1 Preparation for Removing the ITB Bias Roller
Cleaning Blade (Lower)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Detach the process unit cover.
3) Lift the hopper unit.
4) Remove the primary charging assembly. (page 7-86)Reference [Re-
moving the Primary Corona Assembly]
5) Remove the pre-transfer charging assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Remove the drum unit. (page 7-89)Reference [Removing the Drum
Unit]
7) Pull out the fixing/feeding unit.
8) Remove the intermediate transfer unit. (page 7-100)Reference [Remov-
0013-9721 ing the Intermediate Transfer Unit]
9) Remove the ITB cleaning unit. (page 7-99)Reference [Removing the
ITB Cleaning Unit]
10) Remove the ITB cleaner brush (large). (page 7-105)Reference [Re-
moving the ITB Cleaner Brush (Large)]
11) Remove the ITB cleaner brush (small). (page 7-106)Reference [Re-
moving the ITB Cleaner Brush (Small)]
7.14.37.2 Removing the ITB Bias Roller Cleaning Blade
(Lower)
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
[4]
[3]
[1]
F-7-241
[2]
[1]
F-7-242
Chapter 7
0013-9722
[2]
0013-9725
0013-9726
7-107