Canon imagePRESS C1 P Service Manual page 1010

13. CST-ADJ
Subheading
MF-A4R
MF-A6R
MF-A4
14. MISC
Subheading
SEG-ADJ
K-ADJ
DF-S-RK
ACS-ADJ
WT-ER-LV
WT-FL-LM
ACS-EN
ACS-CNT
ACS-EN2
COPIER > ADJUST > CST-ADJ
Enter the basic value of the paper width for the manual feed tray. (A4R)
Adjustment method
- When you executed 'RAM clear' for the DC controller PCB or replaced the DC controller PCB,
enter the value indicated in the service label.
- When you replace the paper width detection VR or newly register a value, execute
FUNCTION>CST in the Service Mode.
Adjustment range: 0 to 255
[Factory setting value / Value after RAM clear: 125]
Enter the basic value of the paper width for the manual feed tray. (A6R)
Adjustment method
- When you executed 'RAM clear' for the DC controller PCB or replaced the DC controller PCB,
enter the value indicated in the service label.
- When you replace the paper width detection VR or newly register a value, execute
FUNCTION>CST in the Service Mode.
Adjustment range: 0 to 255
[Factory setting value / Value after RAM clear: 193]
Enter the basic value of the paper width for the manual feed tray. (A4)
Adjustment method
- When you executed 'RAM clear' for the DC controller PCB or replaced the DC controller PCB,
enter the value indicated in the service label.
- When you replace the paper width detection VR or newly register a value, execute
FUNCTION>CST in the Service Mode.
Adjustment range: 0 to 255
[Factory setting value / Value after RAM clear: 42]
COPIER > ADJUST > MISC
Adjust the separation level for characters and photos at the character/photo/map mode.
Adjustment method
- To make it easier to recognize a photo document, increase the setting value.
- To make it easier to recognize a character document, decrease the setting value.
Adjustment range: -4 to 4
[Factory setting value / Value after RAM clear: 0]
Adjust the black recognition level for black character processing.
Adjustment method
To make it easier to recognize black color, increase the setting value.
Adjustment range: -3 to 3
[Factory setting value / Value after RAM clear: 0]
Set a characteristic value of the paper thickness sensor which was set at a factory.
Since the sensor detection level varies among paper thickness detection sensors, set the sensor
rank information when replacing the sensor or executing DconRAM clear.
Setting range: 1 to 5
Adjust the color recognition level at ACS mode.
Adjustment method
- To make it easier to recognize a black and white document, increase the setting value.
- To make it easier to recognize a color document, decrease the setting value.
Adjustment range: -3 to 3
[Factory setting value / Value after RAM clear: 0]
Set the threshold value to display the waste toner FULL error.
When the number of sheets specified by WT-ER-LV is exceeded, an error (E013) is displayed.
This mode is not used for this machine.
Set the threshold value to display the waste toner FULL warning.
Set the threshold value for the detection of a waste toner box error.
This mode is not used for this machine.
Adjust the ASC judgment area.
Setting range: -2 to +2
[Factory setting value / Value after RAM clear: 1]
Set the chromatic color count area for ASC.
Adjustment range: -2 to +2
[Factory setting value / Value after RAM clear: 0]
Adjust the ACS judgment area. (at DF stream reading)
Adjustment method
When you increase the setting value, the judgment area becomes wider.
Adjustment range: -2 to +2
[Factory setting value / Value after RAM clear: 1]
T-16-115
Contents
T-16-116
Contents
Chapter 16
Level
1
1
1
Level
1
1
1
1
1
1
2
2
2
16-113