Canon imagePRESS C1 P Service Manual page 936

Code
0D90 transparency sensor (front, rear)
0D91 transparency sensor (front, rear)
0D91 registration sensor
0D92 transparency sensor (front, rear)
0D93 transparency sensor (front, rear)
(d) Jam code list (finisher-related)
Code
1001 inlet path sensor feed delay jam
1002 punch path sensor (punch registration sensor) feed delay jam
1004 delivery path sensor feed delay jam
1101 inlet path sensor feed stationary jam
inlet path sensor feed stationary jam
1102
punch path sensor (Punch registration sensor) feed stationary jam
1104 delivery path sensor feed stationary jam
1200 timing jam
1500 stapler staple jam
1300 power-on jam
1400 door open jam
1644 punch jam
1645 punch power-on jam
1791 saddle feed sensor feed delay jam
1792 saddle delivery sensor feed delay jam
1793 saddle inlet sensor feed delay jam
17A1 saddle feed sensor feed stationary jam
17A2 saddle delivery sensor feed stationary jam
17A3 saddle inlet sensor feed stationary jam
1786 saddle stapler staple jam
1787 saddle power-on jam
1788 saddle door open jam
(e) Jam code list (Feeder-specific)
Code
0001 post-separation sensor
0002 post-separation sensor
0003 registration sensor
0004 registration sensor
0005 feed sensor
0006 feed sensor
0007 delivery reversal sensor
0008 delivery reversal sensor
0042 post-separation sensor
0043 registration sensor
0044 registration sensor
Sensor type
Sensor type
Sensor type Sensor notation
PI7
PI7
PI1
PI1
PI8
PI8
PI9
PI9
PI7
PI1
PI1
Sensor
number
PS3, PS29 when the mode is transparency mode
PS3, PS29 when the mode is not transparency mode
PS9 when the mode is transparency mode
PS3, PS29
PS3, PS29
T-16-50
PI33
LED5/PTR5
PI34
PI33
LED5/PTR5
PI34
PI33
STP
PI33,PI34
DOOR
LED5/PTR5
LED5/PTR5
PI18,PI19,PI20
PI11
PI22
PI18,PI19,PI20
PI11,PI17
PI22
S STP
PI11,PI18,PI19,PI20,PI22
DOOR
T-16-51
the post-separation sensor does not detect paper when a feed of 452 mm has been made after
the start of separation.
- the separation sensor detects paper after a feed of "500 mm (if extra length, +200 mm) - 45.5
mm" has been made.
- the sensor goes on within a feed of 12 mm after detection of the trailing edge (holed paper);
the post-separation sensor detects paper when a feed of 50 m has been made after the
separation sensor goes on.
the registration sensor does not detect paper when a feed of 134.8 mm has been made after
the post-separation sensor goes on.
the read sensor goes off before the registration sensor goes off.
- read sensor does not detect paper when a feed of 364.2 mm (182.1 x 2) has been made from
the point of registration.
- the read sensor does not detect paper when a feed of 157.4 mm (78.7 x 2) has been made
from the point of No. 2 registration.
- the read sensor detects paper when a feed of 500 mm (if extra-length, +200 mm) has been
made from the start of feed after a temporary stop at point of reading.
- the read sensor detects paper when a feed of 514 mm has been made after the start of feed
from the standby point in mix mode (LTRR/LGL identified).
- if not in high-speed duplex mode, the delivery sensor does not detect when a feed of 132.1
mm has been made after paper has reached the leading edge downstream roller with respect
to the activation of the read sensor.
- the delivery sensor does not detect paper when a feed of 50 mm has been made after the start
of feed during a switch-back operation.
the delivery sensor detects paper when a feed of 161.9 mm has been made from the end of
reading the trailing edge.
1st; stationary jam at the post-separation sensor
1st; not reaching the registration sensor
1st; stationary at the registration sensor
Remarks
Sensor notation
Description
Chapter 16
16-39