Related Error Code - Canon imagePRESS C1 P Service Manual

9.6.2 Related Error Code

imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / imagePRESS C1+
E-code Main cause
E000 Heating delay error
E001 High temperature detection error
E002 Low temperature detection error
1 (Full-time monitoring)
E003 Low temperature detection error
1 (Mode correspondence)
T-9-3
Detail code Detail
0001 Indicates that the temperature does not increase after the specified time has
passed during the warm-up. (300 sec)
0002 Indicates that the temperature does not increase after the specified time has
passed during the warm-up. (360 sec after reaching warm-up 1)
0003 Indicates that the temperature does not increase after the specified time has
passed during the warm-up. (120 sec after reaching warm-up 2)
0004 Indicates that the temperature does not increase after the specified time has
passed during the warm-up. (360 sec after reaching warm-up 3)
0005 Indicates that the temperature does not increase after the specified time has
passed during the warm-up after the occurrence of jam at the fixing
assembly. (600 sec)
0001 Indicates the fixing roller high temperature detection error. (200 deg C;
Hardware detection)
0002 Indicates the outside heating roller high temperature detection error. (220
deg C; Hardware detection)
0003 Indicates the inlet roller high temperature detection error. (150 deg C;
Hardware detection)
0004 Indicates the outside heating roller edge high temperature detection error.
(220 deg C; Hardware detection)
0005 Indicates the inlet roller edge high temperature detection error. (150 deg C;
Hardware detection)
0011 Indicates the fixing roller high temperature software detection error:
Condition that the temperature of the fixing main thermistor is above 200
deg C for 500msec
0010 Indicates the condition that the temperature of the fixing roller is less than
50 deg C for 1 sec after reaching 80 deg C.
0020 Indicates the condition that the temperature of the outside heating roller is
less than 50 deg C for 1 sec after reaching 80 deg C.
0030 Indicates the condition that the temperature of the inlet roller is less than 50
deg C for 1 sec after reaching 80 deg C.
0041 Indicates the fixing roller low temperature detection while it is in the
standby state: (Detection temperature of either main or sub thermistor)
Condition that the temperature of the fixing roller is less than 130 deg C for
1 sec while it is in the standby state.
0042 Indicates the outside heating roller low temperature detection while it is in
the standby state: (Detection temperature of either main or sub thermistor)
Condition that the temperature of the outside heating roller is less than 160
deg C for 1 sec while it is in the standby state.
0043 Indicates the inlet roller low temperature detection while it is in the standby
state: (Detection temperature of either main or sub thermistor)
Condition that the temperature of the inlet roller is less than 60 deg C for 1
sec while it is in the standby state.
0051 Indicates the fixing roller low temperature detection while performing
black-and-white print: (Detection temperature of either main or sub
thermistor)
Condition that the temperature of the fixing roller is less than 100 deg C for
1 sec while performing black-and-white print.
0052 Indicates the outside heating roller low temperature detection while
performing black and while print: (Detection temperature of either main or
sub thermistor)
Condition that the temperature of the outside heating roller is less than 150
deg C for 1 sec while performing black-and-white print.
0053 Indicates the inlet roller low temperature detection while performing black-
and-white print: (Detection temperature of either main or sub thermistor)
Condition that the temperature of the inlet roller is less than 60 deg C for 1
sec while performing black-and-white print.
Chapter 9
0012-0997
Recovery method
FUNCTION>CLEAR>E
RR
FUNCTION>CLEAR>E
RR
FUNCTION>CLEAR>E
RR
FUNCTION>CLEAR>E
RR
9-31