Canon imagePRESS C1 P Service Manual page 875

Chapter 15
Code
E542 There is an error in up and down movement of the lower tray (finisher/saddle finisher).
8001 There is a clock error in up/down motor of the lower tray.
8002 Area error
0003 Safety switch activation
0004 In the case of detecting fault in clock
0005 In the case of detecting fault in speed
0006 In the case of detecting fault in accelerating time
0007 In the case of detecting Lock Detect signal
E584 There is an error in the shutter unit (finisher/saddle finisher).
8001 The shutter open sensor does not go off (i.e., the shutter is not
0002 The shutter open sensor does not go on (i.e., the shutter does not
E590 There is an error in the punch motor (punch unit).
8001 The punching home position sensor is not detected when the
8002 The puncher does not detect the punching home position after the
E591 There is an error in the punch dust sensor (punch unit).
8001 There is an error in the light-receiving voltage with emission of
8002 There is an error in the light-receiving voltage without emission of
15-12
Cause (Detection Description)
closed).
open).
punch motor has been driven for 200 msec.
motor has stopped (initial operation).
light
light.
Remedy
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
1)Check the shutter home position sensor. Is the sensor normal?
2)Check the wirings between the finisher controller PCB and the
stack edging motor, and between the finisher controller PCB and
the shutter open/closed clutch.
3)Is there a fault in the shutter mechanism?
4)Try replacing the stack edging motor or the shutter open/closed
clutch. Is the problem corrected?
1)Check the shutter home position sensor. Is the sensor normal?
2)Check the wirings between the finisher controller PCB and the
stack edging motor, and between the finisher controller PCB and
the shutter open/closed clutch.
3)Is there a fault in the shutter mechanism?
4)Try replacing the stack edging motor or the shutter open/closed
clutch. Is the problem corrected?
Check the punch home position sensor, the horizontal registration
motor, and the punch driver PCB; then, turn on the main power.
Check the punch home position sensor, the horizontal registration
motor, and the punch driver PCB; then, turn on the main power.
Turn off and then on the main power.
Turn off and then on the main power.