Canon imagePRESS C1 P Service Manual page 1052

Subheading
PJH-P-2
PT-LPADJ
HV-ADOFS
ITB-ACVC
MAIN-DRV
ITB-ROT
ATR-EX
INTR-EX
12. SYSTEM
Subheading
DOWNLOAD
CHK-TYPE
COPIER > FUNCTION > MISC-P
Print out the print job history with detailed information. (for all jobs)
Print out the history of all jobs stored in the copier main unit with detailed information.
[Operation]
Press the item to highlight it, and press the OK key to perform printing.
[Remarks]
The print job history is printed out with detailed information which is not displayed/output in the
job history screen displayed by "system condition > print > job history > printer" and in the print
job history report.
The history of all the recorded jobs (up to 5000 jobs in the BW3/CL2 or later machine) are printed
out.
The difference to PJH-P1 is the number of jobs printed out.
Adjust the initial reflector light volume for the patch detection sensor.
Adjust the initial reflector light volume for the patch detection sensor to a specified value.
Adjust the high pressure AD offset.
Adjust the high pressure AD offset for the primary transfer / secondary transfer / ITB cleaner.
After this mode is executed, the value displayed in the specified item under DISPLAY should be
within + or - 300.
Target items are the following six items under DISPLAY/HV-SYS/.
ITR-CMOF/ITR-VMOF/2TR-CMOF/2TR-VMOF/BCL2CMOF/BCL1CMOF
Forcibly execute the ITB cleaning ACVC.
Forcibly execute ACVC control when the ITB cleaning ACVC is not operating normally.
Drive the intermediate transfer unit and photosensitive drum for a specified period of time.
Press the item to highlight it. Press the OK key and turn the power OFF/ON to execute the
operation. The operation completes after a specified period of time.
Execute the ITB idling.
Execute the ITB idling to prevent incorrect rolling of ITB when keeping the machine in the
storage for a long time.
1) When selecting the item to highlight and pressing OK key, the operation is started.
Forcibly execute the ATR control.
Forcibly execute the ATR control when the correction value for the ATR control is lost after the
E020 error occurs or the DC controller is replaced in the field maintenance service.
1) When selecting the item to highlight and pressing OK key, the operation is started.
Forcibly execute the initial rotation as first power-on.
Forcibly execute the image stabilization control which is executed at the initial rotation as first
power-on.
This mode executes the following image stabilization control.
Electric potential control
Primary transfer ATVC
Developer idling
Patch electric potential control
This operation is executed for approximately one minute.
1) When selecting the item to highlight and pressing OK key, the operation is started.
COPIER > FUNCTION > SYSTEM
Switch the mode to the download mode.
Operation method
1) Select this item.
2) Press the OK key. The machine enters the download mode and waits for a command (waits for
connection). (In this status, STAND-BY (or STNDBY) is displayed next to the small item of
DOWNLOAD.)
3) Perform download using the service support tool. (CONNECTED is displayed during
communication with a PC.)
4) When communication ends, HOLD is displayed. (While HOLD is displayed, the power can be
turned off.)
Specify a partition number to execute HD-CHECK.
Setting range (0 to 65535)
0: Sector checking and recovery of the entire HDD
1: Image storage area
2: Versatile file saving area
3: PDL file saving area
4: Program file saving area
5: MEAP application
6: Aaddress book / Transfer settings
7: MEAP save data
8: System log storage area
Versatile file is data control information such as user setting data, various log data, PDL spool
data, and image data.
Operation method
1) Select this item.
2) Select a partition number using numeric keys.
3) Press the OK key.
Contents
T-16-158
Contents
Chapter 16
Level
1
1
1
1
2
2
2
2
Level
1
1
16-155