Canon imagePRESS C1 P Service Manual page 569

Chapter 9
E-code Main cause
E004 Fixing Main Thermistor short-
circuit/open-circuit error
Thermistor open circuit/heater
open circuit
E005 Web take-up error
E006 Fixing unit connection error
E007 Belt full displacement error
E008 Fixing assembly life error
E009 Power supply connector error
E014 Fixing motor error
9-32
Detail code Detail
0101 Indicates the open-circuit detection at the film side of the fixing main
thermistor.
0102 Indicates the short-circuit detection at the film side of the fixing main
thermistor.
0103 Indicates the open-circuit detection at the case side of the fixing main
thermistor.
0104 Indicates the short-circuit detection at the case side of the fixing main
thermistor.
0010 Indicates the fixing roller thermistor open circuit:
Condition that the difference of the detected temperature between the main
thermistor and sub thermistor of the fixing roller is more than 50 deg C for
500 msec.
0020 Indicates the outside heating thermistor open circuit:
Condition that the difference of the detected temperature between the main
thermistor and the sub thermistor of the outside heating roller is more than
50 deg C for 500 msec.
0030 Indicates the inlet thermistor open circuit:
0040 Indicates the fixing main thermistor foreign substance error:
Condition that the difference of the detected temperature between the main
thermistor and the sub thermistor of the fixing roller is more than 25 deg C
for 500 msec.
0050 Indicates the outside heating thermistor open circuit while it is in the
standby state.
0060 Indicates the inlet thermistor open circuit while it is in the standby state.
0000 Indicates the heater open circuit (triac short error):
000F Condition that the hardware error detection is kept for 200 msec.
bit 0: Outside heater SSR error
bit 1: Fixing sub heater SSR error
bit 2: Fixing main heater SSR error
bit 3: Inlet heater SSR error
0000 Indicates the fixing web absent error:
Indicated when exceeding 4000 counts after the fixing web length detection
detects the web absent state.
0001 Indicates the fixing web drive solenoid open-circuit error.
0001 Indicates that the fixing unit absent state is detected for 500 msec while the
front cover is closed.
0001 Indicates the front side belt full displacement error.
0002 Indicates the rear side belt full displacement error.
0007 Indicates that the double error detections detect the full displacement error.
0010 Indicates that HP detection is not enabled within 1 sec after turning on the
stealing motor.
0100 Indicates HP detection error 1 at the time of initialization.
0200 Indicates HP detection error 2 at the time of initialization.
0001 Indicates the counter value for the fixing roller exceeds the specified value.
(This error is effective when changing the service settings.)
The specified value is determined by the service modes indicated below:
- Warning service mode (FXWRNLVL) 0:180k/1:150k/2:120k [default 0]
- Error service mode (FXERRLVL) 0:+/-20k/1:+/-40k/2:+/-60k/3:error
invalid [default 3]
- ON/OFF of warning display (FXMSG-SW) 0:nondisplay/1:display
[default 0]
0001 Indicates that the power supply identification connector is not inserted or
faulty.
0001 Condition that the motor clock discrepancy is detected for more than 1 sec
after the motor rotates stably.
Recovery method
-
FUNCTION>CLEAR>E
RR
- COUNTER>MISC>FX-
WEB
- COUNTER>DRBL-
1>FX-WEB
FUNCTION>CLEAR>E
RR
COUNTER>DRBL-
1>FX-UP-RL