Canon imagePRESS C1 P Service Manual page 877

Chapter 15
Code
E5F6 There is an error in saddle butting (saddle finisher).
8001 The paper pushing plate home position sensor does not turn on
8002 The paper pushing plate home position sensor does not turn off
8003 The number of detection pulses of the paper pushing plate motor
8004 The paper pushing plate sensor does not turn off when the paper
8005 The paper pushing plate leading edge position sensor does not turn
E5F8 There is an error in the saddle connector (saddle finisher).
0001 The connector of the guide home position sensor is identified as
0002 The connector of the paper pushing plate home position sensor is
0003 The connector of the paper pushing plate leading edge position
E5F9 There is an error in the saddle switch (saddle finisher).
0001 With any of the following sensor is identifying its respective cover
0002 With any of the following sensor is identifying its respective cover
0003 With any of the following sensor is identifying its respective cover
E602 There is a hard disk error
There is a fault in hard disc.
(See 'HDD Error Remedy' of the main controller)
E604 There is a shortage of image memory (SDRAM).
0000 The amount of memory required by the model in question is not
0001 The shortage of memory for MEAP application.
0002 Overload of the image memory.
1024/1536 Fault/lacking in image memory
15-14
Cause (Detection Description)
when the paper pushing plate motor has been driven for 0.3 sec or
more.
Paper pushing plate motor (M8S)/the paper pushing plate home
position sensor (PI14S)
when paper pushing plate motor has been driven for 80 msec or
more.
Paper pushing plate motor (M8S)/the paper pushing plate home
position sensor (PI14S)
clock sensor drops below a specific number.
Paper pushing plate motor (M8S)/the paper pushing plate motor
clock sensor (PI1S)
pushing plate motor has been driven for 80 msec or more.
Paper pushing plate motor (M8S)/the paper pushing plate leading
edge position sensor (PI15S)
on when the paper pushing plate motor has been driven for 0.3 sec
or more.
Paper pushing plate motor (M8S)/the paper pushing plate leading
edge position sensor (PI15S)
being disconnected.
The connector of the guide home position sensor (PI13S)
identified as being disconnected.
The connector of the paper pushing plate home position sensor
(PI14S)
sensor is identified as being disconnected.
The connector of the paper pushing plate leading edge sensor
(PI15S)
a being closed, the inlet cover switch is identified as being open for
1 sec or more after the start of the initial rotation of the machine or
the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
Or, the front cover switch (MS2S) or the delivery cover switch
(MS3S) is open.
The inlet cover switch (MS2S)/front cover switch (MS2S)/
delivery cover switch (MS3S9)
a being closed, the front cover switch is identified as being open
for 1 sec or more after the start of the initial rotation of the machine
or the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
-front cover switch(MS2S)/delivery cover switch (MS3S)
a being closed, the delivery cover switch is identified as being
open for 1 sec or more after the start of the initial rotation of the
machine or the start of printing:
-inlet cover sensor (PI9S)
-front cover open/closed sensor (PI2S)
-delivery cover sensor (PI3S)
-delivery cover switch (MS3S)
recognized.
MEAP application is installed despite of the Base model
Remedy
Check the paper pushing plate motor (M8S)/the paper pushing
plate home position sensor (PI14S).
Check the paper pushing plate motor (M8S)/the paper pushing
plate home position sensor (PI14S).
Check the paper pushing plate motor (M8S)/the paper pushing
plate motor clock sensor (PI1S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate leading edge position sensor (PI15S)
Check the paper pushing plate motor (M8S)/the paper pushing
plate leading edge position sensor (PI15S)
Check the connectors of the guide home position sensor (PI13S).
Check the connectors of the paper pushing plate home position
sensor (PI14S).
Check the connectors of the paper pushing plate leading edge
sensor (PI15S).
Check the inlet cover switch (MS1S)/front cover switch (MS2S)/
delivery cover switch (MS3S).
Check the front cover switch (MS2S)/delivery cover switch
(MS3S).
Check the delivery cover switch (MS3S).
Set it to the size of memory suited to the model in question.
-Modify the configuration to make MEAP as Full model. After
executing uninstallation of the application (i.e., downloading of
the license), set it as MEAP Base.
-Modify the configuration to make MEAP as Full model.
Remove the expanded main memory.
Turn off and then on the main power.
Set it to the size of memory suited to the model in question.
Turn off and then on the main power.