Supplying Toner - Canon imagePRESS C1 P Service Manual

MEMO:
- When the operation is completed, 'OK!' is displayed.
- Execute 'Setting the Paper Cassette' during toner supply.
2) Press the Reset key and exit from the service mode.

2.2.34 Supplying Toner

imagePRESS C1+ (Printer) / imagePRESS C1+
MEMO:
Be sure to perform the following procedure after the machine is placed in
the standby status (Approximately 9 minutes).
1) Execute toner refill (Approximately 2 minutes)
Service mode > FUNCTION > INSTALL > SPLY-H-5
Be sure not to turn the power switch off during the operation.
MEMO:
- When the operation is completed, 'OK!' is displayed.
- Execute 'Setting the Paper Cassette' during toner supply.
2) Exit from service mode.
2.2.35 Setting the Paper Cassette
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Press the cassette release button, and pull out the cassette toward the front.
2) Find out the paper the user uses; then check to be sure that the paper con-
figuration switch [1] of the cassette is in keeping with the paper configu-
ration.
If it is not, change the position to the proper paper configuration
3) Turn the paper size registration dial [2] to the position of the proper paper
size.
4) Hold the lever [1] of the side guide plate and move the side guide plate [2]
to the specified size.
5) Hold the trailing edge guide plate [3] to remove.
Following the display of the underside of the cassette, move the trailing
edge guide plate to the specified size.
[2]
[1]
F-2-226
[3]
0020-4623
6) Affix the appropriate Paper size label [1] to the size plate [2].
7) Deposit papers in the cassette, and put back the cassette.
8) Set other cassettes in the same way.
2.2.36 Setting for K paper
0012-7227
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
Make the following settings for the use of K paper.
1) Enter the service mode (level 2).
2) Change from '0 to 1' in COPIER > OPTION > BODY > KSIZE-SW.
3) Press the reset key to enter (level 1)
4) Set to '0' in COPIER > OPTION > BODY > MODEL-SZ.
MEMO:
Enter the service mode (level 2).
COPIER > OPTION > BODY > KSIZE-SW
The switch for the use of K paper
0: Do not accept K paper (default)
1: Accept K paper
Set the paper size to 8K, 16K in the following service mode.
5) In the case that the paper size is set to 8K
Set to '40' in COPIER > OPTION > CST > CST-U2.
6) In the case that the paper size is set to 16K
Set to '39' in COPIER > OPTION > CST > CST-U1.
7) Turn off/on the main power supply according to the shutdown sequence.
2.2.37 Automatic Gradation Correction Setting
imagePRESS C1 / imagePRESS C1+
1) Clean the copyboard glass.
2) Select Initial Additional Functions > System Settings > Device Manage-
ment Settings > Auto Gradation Adjustment.
MEMO:
'Printer Only' or 'Scanner + Printer' can be selected for 'Auto Gradation
Adjust Method'.
3) Select 'Full Adjust'.
4) Select the source of paper for test print and press 'OK'.
5) Press 'Test print 1'. In a response, test print 1 will be printed.
6) Place the test print 1 on the copyboard glass by following the control pan-
el.
7) Press 'Start scan'. In a response, the test print 1 will be read.
8) When the control panel shows the message that orders removal of the test
print, remove the test print 1 from the copyboard glass.
9) Press 'Test print 2'. In a response, the test print 2 will be printed.
10) Place the test print 2 on the copyboard glass by following the control pan-
Chapter 2
[2]
[1]
F-2-227
[2]
[1]
[2]
F-2-228
0015-8525
0012-7686
2-69