Sweep Setup Menu - Agilent Technologies ENA Series User Manual

Softkey Functions

Sweep Setup Menu

Sweep Setup Menu
Key Operation
Sets the output power level of the internal signal source of the analyzer.
Also displays softkeys for setting up sweeps.
Sets the output power level of the internal signal source of the analyzer.
Power
Displays softkeys for selecting the power range.
*1
Power Ranges
Sets the power range to -15 dBm to 0 dBm.
-15 to 0
Sets the power range to -20 dBm to -5 dBm.
-20 to -5
Sets the power range to -25 dBm to -10 dBm.
-25 to -10
Sets the power range to -30 dBm to -15 dBm.
-30 to -15
Sets the power range to -35 dBm to -20 dBm.
-35 to -20
Sets the power range to -40 dBm to -25 dBm.
-40 to -25
Sets the power range to -45 dBm to -30 dBm.
-45 to -30
Sets the power range to -50 dBm to -35 dBm.
-50 to -35
Returns to the softkey display screen one level higher.
Cancel
Sets the sweep time for each source port. Sweep time mode can be either
Sweep Time
manual or automatic. Inputting the sweep time from the keyboard forces
the analyzer to go into manual mode. In the manual sweep time mode, input
values will be maintained even when measurement conditions change, as
long as the analyzer can handle it. If the sweep time becomes lower than the
analyzer's lower sweep time limit, the sweep time will be reset to the
shortest time within the conditions. If the sweep time exceeds the
analyzer's upper sweep time limit, the sweep time will be reset to the
longest time within the conditions. Inputting the value "0" as the sweep
time causes the analyzer to go into automatic sweep time mode. In this
mode, the sweep time is set to the shortest possible time depending on the
measurement conditions.
Sets the wait time (sweep delay) before starting a sweep for each source
Sweep Delay
port.
Displays softkeys for selecting the sweep mode.
Sweep Mode
Selects the stepped mode.
Std Stepped
Selects the swept mode.
Std Swept
Selects the fast stepped mode.
Fast Stepped
Selects the fast swept mode.
Fast Swept
Returns to the softkey display screen one level higher.
Cancel
Sets the number of points per sweep. The number of points should be from
Points
2 to 1601.
Displays softkeys for selecting the sweep type.
Sweep Type
Selects linear frequency sweep.
Lin Freq
Selects logarithmic frequency sweep.
Log Freq
Selects segment sweep. Segment sweep is a function in which the user can
Segment
define a multiple number of frequency ranges, called segments, each with a
unique number of points, IF bandwidth, power level, delay, sweep mode
and sweep time, and with all segments covered in a single sweep. This
function lets the user skip unnecessary frequency ranges and define optimal
measurement conditions for each segment so that measurement throughput
can be improved.
Returns to the softkey display screen one level higher.
Cancel
446
Function SCPI Command
:SOUR{1-9}:POW
:SOUR{1-9}:POW
:SOUR{1-9}:POW:ATT 0
:SOUR{1-9}:POW:ATT 5
:SOUR{1-9}:POW:ATT 10
:SOUR{1-9}:POW:ATT 15
:SOUR{1-9}:POW:ATT 20
:SOUR{1-9}:POW:ATT 25
:SOUR{1-9}:POW:ATT 30
:SOUR{1-9}:POW:ATT 35
:SENS{1-9}:SWE:TIME
:SENS{1-9}:SWE:DEL
:SENS{1-9}:SWE:GEN STEP
:SENS{1-9}:SWE:GEN ANAL
:SENS{1-9}:SWE:GEN FST
:SENS{1-9}:SWE:GEN FAN
:SENS{1-9}:SWE:POIN
:SENS{1-9}:SWE:TYPE LIN
:SENS{1-9}:SWE:TYPE LOG
:SENS{1-9}:SWE:TYPE SEG
Appendix D