Agilent Technologies ENA Series User Manual page 434

Softkey Functions
Display Menu
Key Operation Function
(Continued)
Allocate Traces
Displays graphs by bisecting the screen horizontally and then bisecting the
right window vertically, with graphs 1, 2, and 3 displayed, respectively, on
the left, in the upper-right corner, and lower-right corner.
Displays graphs by splitting the screen horizontally into four equal parts, with
graphs 1, 2, 3, and 4 displayed from left to right.
Displays graphs by splitting the screen vertically into four equal parts, with
graphs 1, 2, 3, and 4 displayed from top to bottom.
Displays graphs by bisecting the screen both vertically and horizontally with
graphs 1, 2, 3, and 4 in the upper-left, upper-right, lower-left corner, and
lower-right corners, respectively.
Displays graphs by trisecting the screen horizontally and then bisecting each
window vertically, with graphs 1, 2, 3, 4, 5, and 6 displayed.
Displays graphs by bisecting the screen horizontally and trisecting each
window vertically, with graphs 1, 2, 3, 4, 5, and 6 displayed.
Displays graphs by splitting the screen horizontally into four equal parts and
then bisecting each window vertically, with graphs 1, 2, 3, and 4 displayed in
upper windows from left to right, and graphs 5, 6, 7, and 8 displayed in lower
windows from left to right.
Displays graphs by splitting the screen vertically into four equal parts and
then bisecting each window horizontally, with graphs 1, 3, 5, and 7 displayed
in left windows from top to bottom, and graphs 2, 4, 6, and 8 displayed in
right windows from top to bottom.
Displays graphs by trisecting the screen both vertically and horizontally (i.e.,
nine total windows), with graphs 1, 2, and 3 displayed in upper windows
from left to right, graphs 4, 5, and 6 displayed in middle windows from left to
right, and graphs 7, 8, and 9 displayed in lower windows from left to right.
Returns to the softkey display screen one level higher.
Return
Displays softkeys for selecting between data trace and memory trace for on-screen display.
Display
Selects data trace for on-screen display. If the data math option was enabled
Data
in the
Selects memory trace for on-screen display. To store data for a memory trace,
Mem
go back to the previous menu and press
Selects both data trace and memory trace for on-screen display. By storing
Data & Mem
data obtained under certain conditions, it is possible to compare them to new
measurement results (data trace) obtained under different conditions. To store
data for a memory trace, go back to the previous menu and press
Mem
Turns off both the data trace and memory trace.
OFF
Returns to the softkey display screen one level higher.
Cancel
Data ® Mem Stores the measured data for the current active trace in memory. Stored data
can be displayed using the memory trace option. To enable/disable the
memory trace, go to the
Displays softkeys for selecting the types of data processing to be performed.
Data Math
Disables the data processing function. Raw measurement data will be stored
OFF
as a data trace.
Divides the measured data by the memory trace data (normalization) and
Data / Mem
stores the results as a data trace. This function is used to evaluate the ratio
between two traces (e.g., to evaluate gains and attenuations).
426
menu, the computation results will also be displayed.
Data Math
.
menu.
Display
.
Data ® Mem
Data ®
SCPI Command
:DISP:WIND{1-9}:SPL D12_13
:DISP:WIND{1-9}:SPL D1234
:DISP:WIND{1-9}:SPL D1_2_3_4
:DISP:WIND{1-9}:SPL D12_34
:DISP:WIND{1-9}:SPL D123_456
:DISP:WIND{1-9}:SPL D12_34_56
:DISP:WIND{1-9}:SPL D1234_5678
:DISP:WIND{1-9}:SPL
D12_34_56_78
:DISP:WIND{1-9}:SPL
D123_456_789
:DISP:WIND{1-9}:TRAC{1-9}:STAT
:DISP:WIND{1-9}:TRAC{1-9}:MEM
:DISP:WIND{1-9}:TRAC{1-9}:MEM
:DISP:WIND{1-9}:TRAC{1-9}:STAT
:DISP:WIND{1-9}:TRAC{1-9}:MEM
:DISP:WIND{1-9}:TRAC{1-9}:STAT
:CALC{1-9}:MATH:MEM
:CALC{1-9}:MATH:FUNC NORM
:CALC{1-9}:MATH:FUNC DIV
Appendix D