Panasonic MINAS A5 Series Operating Instructions Manual page 59

2.
Applicable Rated
Power
Driver Voltage
motor output
at the
(
*1
rated load
approx.
MDME 7.5kW
11kVA
3-phase,
approx.
MGME 6.0kW
9.0kVA
200V
approx.
MHME 7.5kW
11kVA
MGDH
approx.
MDME 7.5kW
11kVA
3-phase, approx.
MGME 6.0kW
9.0kVA
400V
approx.
MHME 7.5kW
11kVA
approx.
11kW
17kVA
3-phase,
200V
approx.
15kW
22kVA
MHDH MDME
approx.
11kW
17kVA
3-phase,
400V
approx.
15kW
22kVA
without fail, and the circuit breaker should conform to IEC Standards and UL recognized (Listed
and
Suitable for use on a circuit capable of delivering not more than 5,000Arms symmetrical amperes, be-
low the maximum input voltage of the product.
Remarks
Terminal block and protective ground terminals
9mm. (Refer to P.2-50)
Frame
F200V
F400V
G
H
Caution
(Note 1)
Be sure to conduct wiring properly and securely. Insecure or improper wiring may cause the motor
Remarks
running out of control or being damaged from overheating. In addition, pay attention not to allow
conductive materials, such as wire chips, entering the driver during the installation and wiring.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Circuit
Noise
Noise Surge
breaker
absorber
rated
) ( )
signal
current
FS5559-35-33
60A DV0P1450
( Recommended )
component
FN258-42-07
or
30A DV0PM20050
FN258-42-33
DV0P1460
( )
Recommended
RJ8095
component
( Recommended
component
100A T400-61D
(
Recommended
FS5559-80-34
component
DV0P1450
( )
Recommended
component
125A
50A
FN258-42-07
or
DV0PM20050
FN258-42-33
( Recommended )
60A component
marked).
supply (including a load condition).
Driver
Terminal name
L1, L2, Ｌ ３, L1C, L2C, B1, B2, B3, NC, U, V, W
24V、 0V
L1, L2, Ｌ ３, B1, B2, B3, NC, U, V, W
L1C, L2C, 24V, 0V, DB1, DB2, DB3, DB4, NC
L1, L2, Ｌ ３, B1, B2, NC, U, V, W
L1C, L2C, 24V, 0V, DB1, DB2
L1, L2, Ｌ ３, B1, B2, NC, U, V, W
Driver frame
A to E
F, G
H
Applying fastening torque larger than the maximum value may result in damage to the product.
Rated
Diameter Crimp
operating
and terminal
current of
withstand for main
magnetic
voltage of circuit
( )
contactor Contact
main circuit terminal
cable block
*2
11mm or
smaller
100A
（3P+1a）
5.3mm 2 /
AWG10
ø5.3
600 VAC
Terminal
or more
block
60A
M5
（3P+1a）
)
)
16mm or
150A
smaller
（3P+1a）
*5
13.3mm 2 /
AWG6
ø6.4
600 VAC
Terminal
or more
block
100A
*3
M6
（3P+1a）
Terminal block screw
Nominal
size
M5 1.0 to 1.7
M3 0.4 to 0.6
M4 0.7 to 1.0
M5 1.0 to 1.7
M5 2.0 to 2.4
M4 0.7 to 1.0
M6 2.2 to 2.5
Terminal block screw
Nominal
size
M4 0.7 to 0.8
M5 1.4 to 1.6
M6 2.4 to 2.6
Diameter Crimp
Diameter
and terminal Diameter
and
withstand for control
withstand
voltage power withstand
voltage of
of control supply voltage of
motor cable
power terminal brake cable
*4
supply cable block
0.75mm 2 /
10mm or
smaller
AWG18
600 VAC
or more
2
13.3 mm /
ø5.3
AWG6
Terminal
0.75mm 2 / 600 VAC
block
or more
AWG18
M5
100 VAC
or more
0.75mm
AWG18
100 VAC
0.75mm 2 /
or more
10mm or
AWG18
21.1 mm 2 /
smaller
600 VAC
AWG4
600 VAC
or more
or more
13.3 mm 2 /
ø4.3
AWG6
Terminal
2
0.75mm / 600 VAC
block
or more
AWG18
M4
100 VAC
21.1 mm 2 /
or more AWG4
600 VAC
or more
Terminal cover fastening
screw
Nominal
(Note 1) (Note 1)
size
M3 0.19 to 0.21
M3 0.3 to 0.5
M5 2.0 to 2.5
Connector to host
controller (X4)
Nominal
(Note 1) (Note 1)
size
M2.6 0.3 to 0.35
1
and
2
2
/
3
4
5
6
7
2-11