Siemens SINAMICS G150 Manual page 203

Re p0496 = 16: (sin/cos 1 Vpp, EnDat) channel A: 500 mV <--> 21299 dec, channel B: 500 mV <--> 21299 dec
Re p0496 = 17 (resolver): absolute value: 2900 mV <--> 13107 dec, number: 1 ... 8
Re p0496 = 17 (sin/cos 1 Vpp, EnDat): absolute value 500 mV <--> 10650 dec, number: 1 ... 8
Re p0496 = 18 (resolver): angle: signal period <--> 2^16, absolute value: 2900 mV <--> 13107 dec
Re p0496 = 18 (sin/cos 1 Vpp, EnDat): angle: signal period <--> 2^16, absolute value: 500 mV <--> 10650 dec
Re p0496 = 19 (resolver): counter: dec, channel A: 2900 mV <--> 26214 dec
Re p0496 = 19 (sin/cos 1 Vpp, EnDat): counter: dec, channel A: 500 mV <--> 21299 dec
Re p0496 = 22: 180 ° <--> 32768 dec
Re p0496 = 23, 24: r0497.31 (r0499.15) set for at least 1 current controller cycle when encoder zero mark detected
Re p0496 = 24, 25: 500 mV <--> 21299 dec
Re p0496 = 30: Rotary: 1 singleturn measuring step <--> 1 dec, linear: 1 measuring step <--> 1 dec
Re p0496 = 31: Absolute position, incremental in 1/4 encoder pulses
Re p0496 = 32: Zero mark position in 1/4 encoder pulses
Re p0496 = 33: counter offset absolute value in 1/4 encoder pulses
Re p0496 = 40: r0498 <--> (R_KTY/1 kOhm - 0.9) * 32768
Re p0496 = 42: 2500 Ohm <--> 2^32
Re p0496 = 51: 1 rpm <--> 1000 dec
Re p0496 = 52: In 1/4 encoder pulses
Re p0496 = 60: voltage, channel A in mV, voltage, channel B in mV
Re p0496 = 61: Channel A: encoder periods <--> 2^16, channel B: encoder periods <--> 2^16
Re p0496 = 62: encoder periods <--> 2^16
Re p0496 = 70: r: 100% <--> 10000 dec, phase: 180 ° <--> 18000 dec
Re p0496 = 80, 81, 85, 86: 1V <--> 1000 inc
p0496[0...2] Encoder diagnostic signal selection / Enc diag select
VECTOR_G Can be changed: U, T
Data type: Integer16
P-Group: Encoder
Not for motor type: -
Min
0
Description: Selects the trace signal to be output in r0497, r0498 and r0499 for encoder diagnostics.
Value: 0:
1:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24:
25:
30:
31:
32:
33:
40:
41:
42:
51:
52:
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Inactive
r0497: Mechanical revolution
r0498: Raw value track A, r0499: Raw value track B
r0498: Fine position X (-A/2), r0499: Fine position Y (-B/2)
r0498: Fine position Phi, r0499: -
r0498: Offset correction X, r0499: Offset correction Y
r0498: Phase correction X, r0499: Amplitude correction Y
r0498: Cubic correction X, r0499: Fine position X
r0498: oversampling channel A, r0499: oversampling channel B
r0498: fan-out amount, r0499: fan-out number
r0498: Oversampling angle, r0499: Oversampling amount
r0498: Fault counter AB, r0499: raw value track A
r0498: Raw value track C, r0499: Raw value track D
r0498: CD position X (-D/2), r0499: CD position Y (C/2)
r0498: CD position Phi, r0499: CD pos. Phi - mech. revolution
r0497: Zero mark status
r0498: Raw value track R, r0499: Zero mark status
r0498: Raw value track A, r0499: Raw value track R
r0497: Absolute position serial
r0497: Absolute position incremental
r0497: Zero mark position
r0497: Correction absolute position difference
r0498: Raw temperature, r0499: Temperature in 0.1 °C
r0498: Resistance in 0.1 Ohm, r0499: Temperature in 0.1 °C
r0497: Resistance 2500 Ohm
r0497: Absolute speed difference (dn/dt)
r0497: Xact1 corrected quadrants
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
86
2 Parameters
2.2 List of parameters
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
203