Bi: Tm31 Signal Source For Terminal Do 0 / Tm31 S S Do 0; Bi: Tb30 Signal Source For Terminal Do 1 / Tb30 S S Do 1; Bi: Tm31 Signal Source For Terminal Do 1 / Tm31 S S Do 1; Bi: Tb30 Signal Source For Terminal Do 2 / Tb30 S S Do 2 - Siemens SINAMICS G150 Manual

p4030

BI: TM31 signal source for terminal DO 0 / TM31 s s DO 0

TM31 Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for the digital output DO 0 (X542.1, X542.2, X542.3) of Terminal Module 31 (TM31).
Digital output 0 of TM31 is a relay output.
If the signal at the binector input p4030 is low, then terminal COM 0 (X542.2) is connected to NC 0 (X542.1). This
connection also matches the mechanical quiescent setting of the relay.
If the signal at the binector input p4030 is high, then terminal COM 0 (X542.2) is connected to NO 0 (X542.3).
Note: DO: Digital Output
NC: Normally Closed contact
NO: Normally Open contact
p4031

BI: TB30 signal source for terminal DO 1 / TB30 s s DO 1

TB30 Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DO 1 (X481.6) of the Terminal Board 30 (TB30).
Note: DO: Digital Output
p4031

BI: TM31 signal source for terminal DO 1 / TM31 s s DO 1

TM31 Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for the digital output DO 1 (X542.4, X542.5, X542.6) of Terminal Module 31 (TM31).
Digital output 1 of TM31 is a relay output.
If the signal at the binector input p4031 is low, then terminal COM 1 (X542.5) is connected to NC 1 (X542.4). This
connection also matches the mechanical quiescent setting of the relay.
If the signal at the binector input p4031 is high, then terminal COM 1 (X542.5) is connected to NO 1 (X542.6).
Note: DO: Digital Output
NC: Normally Closed contact
NO: Normally Open contact
p4032

BI: TB30 signal source for terminal DO 2 / TB30 s s DO 2

TB30 Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DO 2 (X481.7) of the Terminal Board 30 (TB30).
Note: DO: Digital Output
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
2 Parameters
2.2 List of parameters
Access level: 1
Func. diagram: 9549, 9556
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9102
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9549, 9556
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9102
Unit selection: -
Expert list: 1
Factory setting
0
603