Si Tm54F F-Do Test Stop Mode / Si F-Do Test Mode; Si Tm54F F-Di F-Do Test Stop Configuration / Si Teststop Config; Co/Bo: Si Tm54F Digital Inputs Status / Si Di Status - Siemens SINAMICS G150 Manual

02
03
Dependency: Refer to: p10047
Note: F-DO: Failsafe Digital Output
p10047[0...3]

SI TM54F F-DO test stop mode / SI F-DO test mode

TM54F_MA, Can be changed: C2(95)
TM54F_SL
Data type: Integer16
P-Group: Safety Integrated
Not for motor type: -
Min
1
Description: Sets the test stop mode for the particular safety digital output (F-DO)
Index 0: F-DO 0
Index 1: F-DO 1
Index 2: F-DO 2
Index 3: F-DO 3
Value: 1:
2:
3:
Note: If value = 1:
When this test mode is being used, and excessive resistance of the load between DO+ and DO- can lead to
problems during the test stop. It is therefore important to make sure that the load resistance at an individual F-DO
does not exceed 10 kOhm.
p10048

SI TM54F F-DI F-DO test stop configuration / SI teststop config

TM54F_MA Can be changed: C2(95)
Data type: Integer16
P-Group: Safety Integrated
Not for motor type: -
Min
0
Description: Configures the test stop for F-DI and F-DO of the TM54F.
If the automatic test stop is activated, then the test stop can still be started using binector input p10007.
Note:
The automatic test stop is started after power up, partial power up or a warm restart.
Value: 0:
1:
r10051.0...9

CO/BO: SI TM54F digital inputs status / SI DI status

TM54F_MA, Can be changed: -
TM54F_SL
Data type: Unsigned32
P-Group: Safety Integrated
Not for motor type: -
Min
-
Description: Display and BICO output for the single-channel, logical, and debounced status of the safety digital inputs F-DI 0 ... 9
at Terminal Module 54F (TM54F).
Bit field: Bit
00
01
02
03
04
05
06
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Read back F-DO 2
Read back F-DO 3
Test mode 1 evaluation of int. diagnostic signal (passive load)
Test mode 2 read back F-DO in DI (relay circuit)
Test mode 3 read back F-DO in DI (actuator with feedback signal)
Manual test stop via BICO p10007
Automatic test stop
Signal name
F-DI 0
F-DI 1
F-DI 2
F-DI 3
F-DI 4
F-DI 5
F-DI 6
Test active
Test active
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
3
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
1 signal
Logical 1
Logical 1
Logical 1
Logical 1
Logical 1
Logical 1
Logical 1
2 Parameters
2.2 List of parameters
No test
No test
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
2
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 2850, 2851
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
Logical 0
Logical 0
Logical 0
Logical 0
Logical 0
Logical 0
Logical 0
-
-
FP
2850
2850
2850
2850
2850
2851
2851
989