Intermec Trakker Antares 2460 User Manual page 282

TRAKKER Antares 246X Stationary Terminal User's Manual
backup battery (continued)
temperature range for charging, A-3
understanding, 1-8
bar code labels
ASCII chart, B-6 to B-10
bar code symbologies, enabling, 3-7
conventions, defined, xvii
creating, about start/stop codes, 8-3
decode security, configuring, 8-33
Multiple-Read labels, 7-9
reader commands, troubleshooting, 6-4, 6-8
regular labels, 7-9
rules for creating, 3-5
scanning
accumulating data, 7-3
configuring the terminal, 3-3, 3-5
troubleshooting, 6-11 to 6-12
bar code symbologies
choosing, 3-4
Codabar, configuring, 8-14
Code 11, configuring, 8-15
Code 128, configuring, 8-24
Code 16K, configuring, 8-16
Code 2 of 5, configuring, 8-17
Code 39, configuring, 8-18
Code 49, configuring, 8-22
Code 93, configuring, 8-23
configuration commands, list of, A-8
configuration commands, listed, 8-4
enabling, quick reference, 3-7
list of, A-4
MSI, configuring, 8-55
Plessey, configuring, 8-61
troubleshooting bad decode, 6-4
UPC/EAN, configuring, 8-91
Baud Rate command, 8-9
beep
Beep Volume command, 8-11
sequences, understanding, 1-7
three low beeps, troubleshooting, 6-6
volume, adjusting, 1-7
binary files, converting, 5-8, 7-17, 7-25
binary, table of ASCII characters, B-3 to B-5
Boot Terminal reader command, 7-7
booting the terminal
configuration used, 3-9
9
configuring the button, 6-13, 8-68
definition, 6-13 to 6-14
POST failed, error message, 6-5
turning on the terminal, 2-18
warm boot, 6-14, 7-9
C
cable schematics, A-5
cabled scanners, configuring for scan module, 8-73
I-4
capitalizing characters, with the Keypad Caps Lock
command, 8-52
cautions, defined, xiv
CCD scanners
configuring for scan module, 8-73
list for scanner connector, A-5
CGA-compatible display, described, A-3
change configuration
configuration commands, using, 8-6
reader commands, using, 7-8
Character mode
EOM, described, 4-8, 8-37
troubleshooting, 6-7
character set
characters that change, table of, 8-13
configuration command, 8-12
selecting with the EM9560.BIN application, C-9
charging the backup battery, 2-14
Clear reader command, 7-6
CLIENT.CPP, sample utility, 4-21 to 4-26
Codabar command, 8-14
Code 11 command, 8-15
Code 128 command, 8-24
Code 16K command, 8-16
Code 2 of 5
configuration command, 8-17
disabled with Interleaved 2 of 5, 8-45
Code 39
configuration command, 8-18
creating bar code labels, 8-3
table of ASCII characters, B-3 to B-5
Code 49 command, 8-22
Code 93 command, 8-23
COM ports, locating, 4-6
COM1
connecting to a serial device or network, 2-8
defined, 1-5, 4-6
illustrated, 4-6
COM2
configuring the communications interface, 8-69
connecting to a serial device or network, 2-8
defined, 1-5, 4-6
illustrated, 4-6
Command Processing command, 8-25 to 8-28
commands
configuration commands, using, 8-3
conventions, defined, xvii
reader commands, using, 7-3
communications
monitoring with status lights, 4-14
RF and Ethernet configuration commands, listed,
A-10