0-1048576> {Pbs <Value 0-131072>} {[Color_Blind | Color_Aware]} {Conform [Permit; Replace_Dscp <Value 0-63>] {Counter [Enable | Disable]}} Exceed [Permit {Replace_Dscp; Value 0-63>} | Drop] {Counter [Enable | Disable]} Violate; 131072> Ebs <Value 0-131072> {[Color_Blind | Color_Aware]} {Conform [Permit - Panasonic ZEQUO 6400 Operating Instructions Manual

8. Access Control List (ACL) Egress Command List
config egress_flow_meter [profile_id <value 1-4> | profile_name <name 1-32>] access_id <value 1-
128> [rate <value 0-1048576> {burst_size <value 0-131072>} rate_exceed [drop_packet |
remark_dscp <value 0-63>] | tr_tcm cir <value 0-1048576> {cbs <value 0-131072>} pir <value
0-1048576> {pbs <value 0-131072>} {[color_blind | color_aware]} {conform [permit |
replace_dscp <value 0-63>] {counter [enable | disable]}} exceed [permit {replace_dscp
<value 0-63>} | drop] {counter [enable | disable]} violate [permit {replace_dscp <value 0-
63>} | drop] {counter [enable | disable]} | sr_tcm cir <value 0-1048576> cbs <value 0-
131072> ebs <value 0-131072> {[color_blind | color_aware]} {conform [permit |
replace_dscp <value 0-63>] {counter [enable | disable]}} exceed [permit {replace_dscp
<value 0-63>} | drop] {counter [enable | disable]} violate [permit {replace_dscp <value 0-
63>} | drop] {counter [enable | disable]} | delete]
show egress_flow_meter {[profile_id <value 1-4> | profile_name <name 1-32>] {access_id
<value1-128>}}
create port_group id <value 1-64> name <name 16>
config port_group [id <value 1-64> | name <name 16>] [add | delete] [<portlist> | all]
delete port_group [id <value 1-64> | name <name 16>]
show port_group {id <value 1-64> | name <name 16>}
8.1. create egress_access_profile
 Description
This command is used to create an egress access list profile. For example, for some
hardware, it may be invalid to specify destination IPv6 address and source IPv6
address at the same time. The user will be prompted for these limitations.
 Format
create egress_access_profile profile_id <value 1-4> profile_name <name 1-32>
[ethernet {vlan {<hex 0x0-0x0fff>} | source_mac <macmask 000000000000-ffffffffffff>
| destination_mac <macmask 000000000000-ffffffffffff> | 802.1p | ethernet_type} |
ip {vlan {<hex 0x0-0x0fff>} | source_ip_mask <netmask> | destination_ip_mask
<netmask> | dscp | [icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-
0xffff> | dst_port_mask <hex 0x0-0xffff> | flag_mask [all | {urg | ack | psh | rst | syn |
fin}]} | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} |
protocol_id_mask <hex 0x0-0xff> {user_define_mask <hex 0x0-0xffffffff>}]} | ipv6
{class | source_ipv6_mask <ipv6mask> | destination_ipv6_mask <ipv6mask> | [tcp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | udp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | icmp {type |
code}]}]
118