Utility Commands - Panasonic ZEQUO 6400 Operating Instructions Manual

84.Utility Commands

This chapter describes the following utility commands.

Downloading and uploading firmware, configuration files, and log files using
TFTP or RCP server
 Selecting firmware and configuration files used during a boot

RCP server settings

Ping, traceroute for IPv4 or IPv6

Logging in to the Telnet server

Ping response settings to broadcast address
download [firmware_fromTFTP [<ipaddr> | <ipv6addr> | <domain_name 255>] src_file
<path_filename 64> {[unit <unit_id 1-4> | all]} {dest_file <pathname>} {boot_up} |
cfg_fromTFTP [<ipaddr> | <ipv6addr> | <domain_name 255>] src_file <path_filename 64>
{[unit <unit_id 1-4> | all]} {[increment | dest_file <pathname>]}]
download cfg_fromRCP [{username <username>} {<ipaddr>} src_file <path_filename 64> |
rcp:<string 128>] {[unit <unit_id 1-4> | all]} {dest_file <pathname>}
download firmware_fromRCP [{username <username>} {<ipaddr>} src_file <path_filename 64> |
rcp:<string 128>] {[unit <unit_id 1-4> | all]} {dest_file <pathname>} {boot_up}
upload [cfg_toTFTP [<ipaddr> | <ipv6addr> | <domain_name 255>] dest_file <path_filename 64>
{unit <unit_id>} {src_file <pathname>} {[include | exclude | begin] <filter_string 80>
{<filter_string 80> {<filter_string 80>}} {[include | exclude | begin] <filter_string 80>
{<filter_string 80> {<filter_string 80>}} {[include | exclude | begin] <filter_string 80>
{<filter_string 80> {<filter_string 80>}}}}} | log_toTFTP [<ipaddr> | <ipv6addr> |
<domain_name 255>] dest_file <path_filename 64> | attack_log_toTFTP [<ipaddr> |
<ipv6addr> | <domain_name 255>] dest_file <path_filename 64> {unit <unit_id 1-4>} |
firmware_toTFTP [<ipaddr> | <ipv6addr> | <domain_name 255>] dest_file <path_filename
64> {unit <unit_id 1-4>} {src_file <pathname>}]
upload attack_log_toRCP [{username <username>} {<ipaddr>} dest_file <path_filename 64> |
rcp:<string 128>] {unit <unit_id 1-4>}
upload cfg_toRCP [{username <username>} {<ipaddr>} dest_file <path_filename 64> |
rcp:<string 128>] {unit <unit_id 1-4>} {src_file <pathname>} {[include | exclude | begin]
<filter_string 80> {<filter_string 80> {<filter_string 80>}} {[include | exclude | begin]
<filter_string 80> {<filter_string 80> {<filter_string 80>}} {[include | exclude | begin]
<filter_string 80> {<filter_string 80> {<filter_string 80>}}}}}
upload firmware_toRCP [{username <username>} {<ipaddr>} dest_file <path_filename 64> |
rcp:<string 128>] {unit <unit_id 1-4>} {src_file <pathname>}
upload log_toRCP [{username <username>} {<ipaddr>} dest_file <path_filename 64> |
rcp:<string 128>]
config firmware image {unit <unit_id 1-4>} <pathname> boot_up
config configuration {unit <unit_id 1-4>} <pathname> [boot_up | active]
show config [effective | modified | current_config | boot_up | file <pathname>] {[include |
exclude | begin] <filter_string 80> {<filter_string 80> {<filter_string 80>}} {[include | exclude
| begin] <filter_string 80> {<filter_string 80> {<filter_string 80>}} {[include | exclude |
begin] <filter_string 80> {<filter_string 80> {<filter_string 80>}}}}}
show boot_file
config rcp server {ipaddress <ipaddr> | username <username>}
config rcp server clear [ipaddr | username | both]
927
84. Utility Commands