YOKOGAWA MuR10000 Manual page 271

pen offset compensating data, ejection of ......................... 1-22
pen offset compensation ........................................... 1-15, 7-9
periodic inspection ............................................................. 11-1
periodic printout ........................................... 1-18, 9-17, App-1
periodic printout, disabling of ............................................. 7-14
periodic printout interval ........................................ 7-14, App-6
plotter pen............................................................................ 3-8
POC ..................................................................................... 7-9
portable type ........................................................ 12-16, 12-24
power and other computations ............................................ 9-5
power (computation) .......................................................... 1-26
power failure ....................................................................App-5
power supply ................................................................... 12-18
power switch ...................................................................... 2-13
precautions (input signal wiring) .......................................... 2-4
precautions (optional terminal wiring) .................................. 2-8
precautions (power supply wiring) ..................................... 2-11
printing a message ............................................................ 3-16
printing the computed value .............................................. 9-22
printing the recorder settings ............................................. 3-14
printout contents ................................................................ 1-16
printouts ............................................................................. 12-5
printout using the TLOG timer .........................................App-4
protective ground terminal ................................................. 2-12
R
range type............................................................................ 1-2
rear panel ............................................................................ 3-3
recorder ............................................................................... 1-1
recorder's version ....................................................................ii
recording............................................................................ 1-13
recording color ....................................... 1-14, 7-8, 7-11, 9-23
recording (computation channels) ..................................... 1-27
recording span ..................................................................... 1-2
recording start printout....................................................... 1-19
recording zone ........................................................... 6-5, 9-15
reference junction compensation......................................... 1-4
reference pen .................................................................... 1-15
reference time.................................................................... 7-14
reflash alarm .............................................................. 1-10, 7-3
registering display types to screens .................................... 8-3
relational computation ............................................... 1-26, 9-6
relative time mode ............................................................. 9-21
relay contact input ............................................................. 2-10
relay contact output ........................................................... 2-10
relay numbers .......................................................... 5-11, 9-12
releasing the alarm output ................................................. 3-18
releasing the key lock ........................................................ 3-19
remaining chart length ....................................................... 11-1
remote control.......................................................... 1-30, 7-28
remote control input ........................................................... 2-10
remote control input terminals ............................................. 2-9
remote signal ..................................................................... 1-31
replacement period for expendable parts ........................ 11-10
replacing felt pens ............................................................... 3-7
replacing the internal light LED.......................................... 11-3
replacing the plotter pen ...................................................... 3-8
report data ............................................................... 7-14, 9-26
report mode .....................................................................App-2
resetting the computed values............................................. 9-1
resetting the report data .................................................... 3-17
resetting the TLOG computed value .................................. 9-22
revise values, setting using ............................................... 6-15
revisions ...................................................................................i
ribbon cassette .................................................................. 3-10
ribbon feeding knob ........................................................... 3-10
ribbon is loose ................................................................... 3-10
IM 04P01B01-01E
RJC ...................................................................................... 7-7
RTD ..................................................................................... 5-2
run modes............................................................................ 4-1
S
safety precautions .................................................................. iii
safety standards ..................................................................... iii
safety symbols ........................................................................ iii
scale printout ...................................................................App-2
scaling ................................................................................. 1-3
scan interval ........................................................................ 1-2
SD memory card................................................................ 1-23
secondary chart speed ...................................................... 6-10
Setting complete screen ...................................................... 4-3
setting mode ........................................................................ 4-1
settings necessary to use various functions ...................... 1-34
Setup ................................................................................. 3-14
setup guide ........................................................................ 1-34
setup items (basic setting mode) ....................................... 4-11
setup Items (setting mode) .................................................. 4-9
shunt resistor ....................................................................... 1-2
skip ...................................................................................... 5-8
sprocket teeth ...................................................................... 3-5
square root ........................................................................ 1-26
square root computation .............................................. 1-3, 5-7
square root low-cut function .............................................. 7-24
standard accessories............................................................. vii
standard performance ..................................................... 12-20
standard temperature device ............................................. 11-5
starting the computation ...................................................... 9-1
start printout............................................................. 1-22, 6-16
start printout 2.................................................................... 6-16
start recording.................................................................... 3-11
status display ..................................................................... 1-24
status of the remote control input terminal .......................... 9-5
stoppers ............................................................................... 3-4
stopping the computation .................................................... 9-1
stop recording .................................................................... 3-11
suffix code ..............................................................................vi
SUM scale ..................................................... 7-14, 9-14, 9-26
supported standards ........................................................ 12-19
switching the display screen .............................................. 3-12
T
tag.................................................................... 6-8, 7-11, 9-18
TC ........................................................................................ 5-2
temperature unit ................................................................ 7-42
thermocouple ....................................................................... 5-2
thermocouple input .............................................................. 2-5
time constant ....................................................................... 6-3
time printout format.................................................. 1-18, 7-26
timer ................................................................................... 9-21
time tick ................................................................. 1-16, App-1
time tick cancel mark ............................................. 1-16, App-1
TLOG computation .................................................... 1-26, 9-8
transistor input ................................................................... 2-10
trend recording ...................................... 1-14, 6-7, 9-17, 12-4
trend recording interval .............................................. 1-14, 6-1
trigger ................................................................................ 1-31
troubleshooting .................................................................. 10-4
type of measured values ................................................... 7-14
type of report data ............................................................. 9-26
types of computations........................................................ 1-26
types of inputs ..................................................................... 1-2
Index
1
2
3
4
5
6
7
8
9
10
11
12
App
Index
Index-3