Chapter 10 Troubleshooting; A List Of Error Messages - YOKOGAWA MuR10000 Manual

Chapter 10 Troubleshooting

10.1 A List of Error Messages

Setting Errors
Code Message
1 System error.
2 Incorrect date or time setting.
3 A disabled channel is selected.
4 Incorrect function parameter.
5 The input numerical value exceeds the set range.
6 Incorrect input character string.
7 Too many characters.
8 Incorrect input mode.
9 Incorrect input range code.
10 Format error.
11 Range settings are not same within the selected
channels.
12 An invalid characters.
13 Ref. CH error.
15 Too many characters for printout.
16 Too many characters for message.
21 Cannot set an alarm for a SKIPPED channel.
22 The upper and lower span limits are equal.
23 The upper and lower scale limits are equal.
24 The lower span limit is greater than the upper span
limit.
25 The lower scale limit is greater than the upper scale
limit.
26 Bias cannot be set to the SKIPPED channel.
27 Bias cannot be set to the DI channel.
30 The partial boundary value exceeds the range of the
span.
31 Partial is invalid on the SKIPPED channel.
35 The upper and lower limits of the printing zone are
equal.
36 The lower limit of the printing zone is greater
than the upper limit.
37 The printing zone is narrower than the minimum
width (5 mm).
38 Partial is invalid on the DI channel.
39 The bias and the calibration cannot be used
simultaneously.
40 Datume value (1 >= 2)
41 Datume value (n-1 > n)
42 Revise value (n-1 >= n)
47 All items in DISP menu parameters are set to SKIP.
48 Start = Finish.
49 Invalid or missing DST time settings.
61 There is no channel specified by the MATH
expression.
62 MATH expression grammar is incorrect.
63 MATH expression sequence is incorrect.
IM 04P01B01-01E
There are cases in which error codes and messages are displayed on the screen during
operation. The error messages and their description are listed below.
Explanation/Countermeasures
Contact your nearest YOKOGAWA dealer.
Check the setting.
The channel does not exist.
Incorrect communication parameter.
–
The entered character cannot be used.
–
Incorrect range mode (Volt, TC, Scale, etc.) setting.
Incorrect range type (2 V, R, PT100, etc.) setting.
Incorrect character string format.
Channels whose range differs cannot be set simultaneously.
Contains an invalid character.
Specify a channel whose range is set to voltage, TC, or RTD for
the reference channel.
Too many characters in the message printout including
measured/computed values.
Cannot enter a setting that exceeds the message string (16
characters).
–
This is not allowed.
This is not allowed.
–
–
–
–
–
–
Set the rightmost value of the zone – the leftmost value ≥ 5 mm.
Set the rightmost value of the zone – the leftmost value ≥ 5 mm.
Set the rightmost value of the zone – the leftmost value ≥ 5 mm.
–
–
Set the correction point (measured value) of the first point less
than that of the second point in the calibration correction.
Set the correction point (measured value) of the n–1
th
than or equal to that of the n point in the calibration correction.
Set the correction value of the n–1
point in the calibration correction.
–
The DST start time and end time cannot be set to the same time.
Since the time gains one hour when the DST starts, the set-up
time does not exist.
Set a computation channel.
Enter the equation correctly.
Enter the equation correctly.
th
point less
th th
point less than that of the n
10-1
1
2
3
4
5
6
7
8
9
10
11
12
App
Index