Table of Contents
Advertisement
GP 15 Setting the Machine for a Time & Materials (T & M)
Account
Description
This procedure sets the machine for a T&M Account.
NOTE: If the Customer was on a FSWA and is now a T & M, the message "Draw Type Mis-
match" will appear on the UI. To remove this message and continue the make copies, the Cus-
tomer will need to order a T & M Xerographic CRU.
Procedure
1.
While holding down the "0" Button, press Start. A screen displays asking you to Enter
your Access Number.
2.
Using the Keypad, enter 6789.
3.
Press Confirm when finished. If you make a mistake press "C". The Customer Support
Engineer Tools screen will display.
4.
Press the NVM Read/Write button in the center of the top row. The NVM Read/Write
(dC131) screen will display.
5.
Press the Enter Number button to begin.
6.
Using the Keypad, enter 774-056.
7.
Press Start to bring up the current value. The Current Value will display in the box on the
Left. If the current value is 48 the machine setup for a Full Service Maintenance Agree-
ment FSMA account.
8.
Using the Keypad press 49 to set the account to T & M.
9.
The number you entered will display in the New Value box on the right.
10. Press Start to accept the change. The number should now appear in the Current Value
box.
11. Press Close to exit this screen.
12. After you press Close, the machine will re-start.
13. When the screen returns, press Done to finish.
14. The machine will now re-start and will recognize the account as T & M.
Reissue
DocuColor 12/DCCS50
GP 16 Setting the Machine to recognize the Sorter as a
Mailbox
Description
This procedure configures the machine to recognize the Sorter as a Mailbox.
NOTE: This procedure cannot be used with a Copier only configuration.
NOTE: This procedure uses the machine UI to set the machine to recognize the Sorter as a
Mailbox. To set the machine to recognize the Sorter as a Mailbox using the PWS, use the alter-
nate procedure below.
Procedure
1.
While holding down the "0" Button, press Start. A screen will display, asking you to Enter
your Access Number.
2.
Using the Keypad, Enter 6789.
3.
Press Confirm when finished. If you make a mistake, press "C". The Customer Support
Engineer Tools screen will display.
4.
Press the NVM Read / Write button in the center of the top row.
5.
The NVM Read / Write (dC131) screen will display.
6.
Press the Enter Number button to begin.
7.
Using the Keypad, enter 780-001.
8.
Press Start to bring up the current value. The Current Value will appear in the box on the
left. If the current value is "0" the device is set up as a Sorter.
9.
Using the Keypad, press "1" to set the device up as a Mailbox. The number you entered
will appear in the New Value box on the right.
10. Press Start to accept the change. The new number should now appear in the Current
Value.
11. Press Close to exit this screen.
12. After you press Close the machine will re-start.
13. When the screen returns press Done to finish.
14. The machine will re-start and will recognize the devise as a Mailbox.
NOTE: The procedure below is an alternate method for setting the machine to recognize the
Sorter as a Mailbox using the PWS.
Procedure
1.
Enter the Service Diagnostics Mode, refer to:
using the
PWS.
2.
Select Configuration Page (dC371) from the DC Quick pull down menu.
3.
Select Mailbox from "Output Devices(s)".
4.
Select the Save Button.
1/05
GP 15 Setting the Machine for a Time & Materials (T
6-15
Entering the Service Diagnostic Mode
General Procedures
Advertisement
Table of Contents
Troubleshooting
