Table of Contents
Advertisement
11-302 Front Cover B Interlock Open RAP
Front Cover B Interlock Open Failure. This status code is declared when the Mail Box Front
Cover is open.
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D,
Door Interlock Open RAP
to troubleshoot this Fault Code.
Initial Actions
•
Refer to BSD11.1 for the following procedure.
•
Ensure that
P/J551
on the Mail Box Control PWB, and
Cover Interlock Switch are connected before beginning this RAP.
•
Check the Front Cover for proper alignment.
•
Verify that the Front Cover closes properly.
Procedure
Enter dC330 011-301 Mailbox Front Cover Intlk Sw. The state of the Mail Box Front Cover
Interlock Switch is Low and switches to High when the Mail Box Front Cover is opened.
Y
N
With the Front Cover closed, there is +0 VDC between P/J551-2 on the Mail Box
Control PWB and GND.
Y
N
Go to the
Flag 1
on BSD 11.1. Check the wires for an open circuit. If the wires are
good, replace the Mail Box Front Cover Interlock Switch
continues, replace the Mail Box Control PWB
Check the Mail Box Front Cover Interlock Switch for intermittent operation. Ensure that the
switch and the cover are properly aligned and adjusted. If the problem continues, replace
the Mail Box Control PWB
(PL
13.10).
Check the Mail Box Front Cover Interlock Switch for intermittent operation. Ensure that the
switch and the cover are properly aligned and adjusted. If the problem continues, replace the
Mail Box Control PWB
(PL
13.10).
Status Indicator RAPs
11-302 Front Cover B Interlock Open RAP, 11-303
11-302 Decurler
P/J564
on the Mail Box Front
(PL
13.4). If the problem
(PL
13.10)
1/05
2-204
manuals4you.com
manuals4you.com
11-303 Docking Interlock Open RAP
Docking Interlock Open failure. This status code is declared when the Mail Box is not properly
docked.
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D,
Interlock Open RAP
to troubleshoot this Fault Code.
Initial Actions
•
Refer to BSD11.1 for the following procedure.
•
Ensure that
P/J570
on the Mail Box Control PWB,
Docking Interlock Switches, and
before beginning this RAP.
•
Check the Mail Box for proper alignment.
Procedure
Enter dC330
011-303 Mailbox Docking INTLK
Docking Interlock Switches is High and changes to Low when the Mail Box is undocked.
Y
N
With the Mail Box docked, there is +5 VDC between P/J570-B7 on the Mail Box
Control PWB and GND.
Y
N
Disconnect
P/J665
from the Mail Box Docking Interlock Switch 2. With
Box docked, there is +5 VDC between P/J570-B7 on the Mail Box Control PWB
and GND.
Y
N
Disconnect
P/J664
from the Mail Box Docking Interlock Switch 1. With
Mail Box docked, there is +5 VDC between P/J570-B7 on the Mail Box
Control PWB and GND.
Y
N
Go to the
Flag 2
on BSD 11.1. Check the wires for an short circuit to
ground. If the wires are good, replace the Mail Box Control PWB
13.10).
Replace the Mailbox Docking Interlock Switch 1
Replace the Mailbox Docking Interlock Switch 2
Check the Mail Box Docking Interlock Switches for intermittent operation. Ensure that the
switches are properly aligned and adjusted. If the problem continues, replace the Mail Box
Control PWB
(PL
13.10).
Check the Mail Box Front Cover Interlock Switch for intermittent operation. Ensure that the
switch and the cover are properly aligned and adjusted. Check that the Mail Box is standing on
an even floor. Adjust Castors if necessary. If the problem continues, replace the Mail Box Con-
trol PWB
(PL
13.10).
11-303 Docking
P/J665
and
P/J664
on the Mail Box
P/J652
on the Decurler Control PWB are connected
Switches. The status of the Mail Box
(PL
13.12).
(PL
13.12).
DocuColor 12/DCCS50
the
Mail
the
(PL
Reissue
Advertisement
Table of Contents
Troubleshooting
