Xerox DocuColor 12/DCCS50 Service Manual page 732

Table 1 PH NVM List (761)
Chain-
Link Name Default
761-067 ADJUST DUPLEX 16
OUT MOTOR OFF
TIMING(FROM
DUPLEX OUT
SENSOR ON)
761-068 ADJUST DUPLEX 246
OUT MOTOR ON
START TIM-
ING(FROM
DUPLEX TRAY)
761-069 SPAREINVERT 383
MOTOR ON TIM-
ING(DUPLEX
MODE: PITCH
1500ms ONLY)
761-090 TAKE AWAY 3 15
CLUTCH ON TIM-
ING(USED TRAY 4)
761-091 TAKE AWAY 2 20
CLUTCH ON TIM-
ING(USED TRAY 4)
General Procedures
dC131PH NVM List (761)
Range Description
0-85 Time from Duplex Out Sensor ON to
Duplex Out Motor OFF (Duplex Wait Point
stop position - Adjustment)
Default=32ms
Range=0-170ms (±40ms) (0-85)
Unit=2ms/step
Default DATA=16 (Quadrant MC
CLK)
221-271 Duplex Out Motor ON start time to send
paper from the Duplex Tray (Duplex Feed
start timing)
Default=492 ms
Range=442-542ms (±50ms) (221-
271)
Unit=2ms/step
Default DATA=246 (Quadrant MC
CLK)
380-386 Time from Registration Motor ON using
Pitch 1500ms Single Leaf Duplex(*4) to
Invert Motor ON (Duplex inversion start
timing)
Default=3830ms
Range=3800-3860ms (±30ms) (380-
386)
Unit=10ms/step
Default DATA=383 (10ms RTMR)
(*4)40 PPM MODE
10-20 Time from #4 Take Away Feed Clutch ON
to #3 Take Away Feed Clutch ON
Default=150ms
Range=100-200ms (10-20)
Unit=10ms/step
Default DATA=15 (10ms RTMR)
15-25 Time from #3 Take Away Feed Clutch ON
to #2 Take Away Feed Clutch ON (Feed
from #4 Tray)
Default=200ms
Range=150-250ms (15-25)
Unit=10ms/step
Default DATA=20 (10ms RTMR)
Chain-
Link Name
761-092 TAKE AWAY 2
CLUTCH ON TIM-
ING(USED TRAY 3)
761-095 ADJUST REGI
LOOP(From Tray 5
Postcard)
761-101 ARRIVE AT TRAY 1
PRE FEED SEN-
SOR 1(USED
TRAY 1)
761-102 ARRIVE AT TRAY 1
PRE FEED SEN-
SOR 2(USED
TRAY 1)
761-103 ARRIVE AT TRAY 1
PRE FEED SEN-
SOR 3(USED
TRAY 1)
1/05
6-52
manuals4you.com manuals4you.com
Table 1 PH NVM List (761)
Default Range Description
15 10-20 Time from #3 Take Away Feed Clutch ON
to #2 Take Away Feed Clutch ON (Feed
from #3 Tray)
Default=150ms
Range=100-200ms (10-20)
Unit=10ms/step
Default DATA=15 (10ms RTMR)
58 33-83 Time from Registration SNR ON to Main
Motor 2 OFF (Registration Loop adjust-
ment - Tray 5: Postcard)
Default=116ms
Range=±50ms (±25)
Unit=2ms/step
Default DATA=58 (2ms RTMR)
0 None Measurement result: Timing from #1 Tray
Pre-Feed start to #1 Pre-Feed SENSOR
ON
Theoretical value=115ms
JAM TIMER=408ms (50PPM,
12.5PPM B side) = 458ms (Other)
Unit=0.5ms/step (Normal paper)
Last storage location - see 761-351.
0 None Measurement result: Timing from #1 Tray
Pre-Feed start to #1 Pre-Feed SENSOR
ON
Theoretical value=115ms
JAM TIMER=408ms (50PPM,
12.5PPM B side) = 458ms (Other)
Unit=0.5ms/step (Normal paper)
Last storage location - see 761-351.
0 None Measurement result: Timing from #1 Tray
Pre-Feed start to #1 Pre-Feed SENSOR
ON
Theoretical value=115ms
JAM TIMER=408ms (50PPM,
12.5PPM B side) = 458ms (Other)
Unit=0.5ms/step (Normal paper)
Last storage location - see 761-351.
DocuColor 12/DCCS50
Reissue