Xerox DocuColor 12/DCCS50 Service Manual page 1186

A B C
Replace the Eject Paddle Home Sensor
replace the Finisher PWB (PL 18.4).
Disconnect P/J1055. The display is High.
Y N
Go to Flag 6 on BSD12.14. Check the wire for a short circuit to GND. If the wire is
good, replace the Finisher PWB
Replace the Eject Paddle Home Sensor
Check the actuator for the Eject Paddle Home Sensor for binding as it moves in and out of the
sensor. Ensure that the actuator is secured to the shaft.
Go to Flag 5 and Flag 6 on BSD 12.14. Check for an intermittent short circuit or loose connec-
tions. If the problem continues, replace the Eject Paddle Home Sensor
Finisher/Sorter
12-251 , 12-253
(PL 18.19). If the problem continues,
(PL 18.4)
(PL 18.19).
(PL 18.19).
12-253 RAP
When one of the following occur:
• The Tamper Home Sensor detects that the Tamper remained in the Home position
800msec after Tamper Motor On.
• The Tamper is not detected in the Home position after the Tamper cycle is complete.
Initial Actions
NOTE: It is much easier to access the Tamper components if the Stacker Assembly is
removed. Refer to REP 15.2.2
Refer to BSD 12.1 and 12.11 for the following procedure.
Procedure
Do not continue to press the Start button after the Tamper reaches either the fully-forward or
fully-rearward position.
Push the Tamper towards the rear of the Finisher. Enter dC330 012-060 Tamper Motor Low
Front. Press Start. The Tamper moves toward the front each time the Start button is
pressed.
Y N
There is 24 VDC from P/J1087- 3 to GND and from P/J1087-6 to GND.
Y N
Go to Flag 6 on BSD 12.11. Check for an open circuit.
Go to Flag 5 on BSD 12.11. Check for an open circuit or a short circuit to GND. If the wires
are good, Replace the Tamper Motor
Finisher PWB (PL 18.4).
Enter dC330 012-062 Tamper Motor Low Rear. Press Start. The Tamper moves toward the
rear each time the Start button is pressed.
Y N
Go to Flag 5 on BSD 12.11. Check for an open circuit or a short circuit to GND. If the wires
are good, Replace the Tamper Motor
Finisher PWB (PL 18.4).
Enter dC330 012-061 Tamper Motor Top Front. Press Start. The Tamper moves toward the
front each time the Start button is pressed.
Y N
Go to Flag 5 on BSD 12.11. Check for an open circuit or a short circuit to GND. If the wires
are good, Replace the Tamper Motor
Finisher PWB (PL 18.4).
Enter dC330 012-063 Tamper Motor Top Rear. Press Start. The Tamper moves toward the
rear approximately 30-50 mm each time the Start button is pressed.
Y N
Go to Flag 5 on BSD 12.11. Check for an open circuit or a short circuit to GND. If the wires
are good, Replace the Tamper Motor
Finisher PWB (PL 18.4).
A
1/05
8d-44
manuals4you.com manuals4you.com
for this procedure.
CAUTION
(PL 18.16). If the problem continues, replace The
(PL 18.16). If the problem continues, replace The
(PL 18.16). If the problem continues, replace The
(PL 18.16). If the problem continues, replace The
DocuColor 12/DCCS50
Reissue