Xerox DocuColor 12/DCCS50 Service Manual page 1148

A G H I J
Go to Flag 5 on BSD12.7. Check the wires for an open circuit. If the wires
are good, replace the Mailbox Gate Solenoid
Go to Flag 5 on BSD12.7. Check the wires for an open circuit. If the wires are
good, ensure that the Mailbox gate is connected to the Mailbox Gate Solenoid
and that it moves freely. If the problem continues replace the Mailbox Gate
18.11) and the Mailbox Gate Solenoid
Ensure that the Mailbox gate is connected to the Mailbox Gate Solenoid and that it
moves freely. If the problem continues replace the Mailbox Gate
Mailbox Gate Solenoid (PL 18.11).
The Finisher Gate is in the Down position
Y N
Enter dC330 012-070 Finisher Gate Solenoid Closed. Press Start. The
Gate Solenoid energized.
Y N
+24 VDC is measured between P/J1042-16 and P/J1042-14 on the Fin-
isher PWB.
Y N
+24 VDC is Measured between P/J1042-16 on the Finisher PWB and
GND
Y N
+24 VDC is measured between P/J1042-14 on the Finisher PWB
and GND.
Y N
Go to the +24 VDC Wirenet and troubleshoot the wire between
P/J1042-14 on the Finisher PWB and P/J45-6 on the Distribu-
tion PWB
Replace the Finisher PWB
Less than +1 VDC is measured between P/J1042-16 on the Finisher
PWB and GND
Y N
Replace the Finisher PWB
Go to Flag 5 on BSD12.7. Check the wires for an open circuit. If the wires
are good, replace the Finisher Gate Solenoid
Go to Flag 5 on BSD12.7. Check the wires for an open circuit. If the wires are
good, ensure that the Finisher gate is connected to the Finisher Gate Solenoid
and that it moves freely. If the problem continues replace the Finisher Gate
18.11) and the Finisher Gate Solenoid
Ensure that the Finisher Gate is connected to the Finisher Gate Solenoid and that it
moves freely. If the problem continues replace the Finisher Gate
Finisher Solenoid (PL 18.11).
• Check the paper path for any obstructions that could cause the paper to enter the
Vertical Transport.
A
Finisher/Sorter
11-107 SCT Exit Sensor On Jam Long RAP
(PL 18.11).
(PL
(PL 18.11).
(PL 18.11) and the
Finisher
(PL 18.4)
(PL 18.4)
(PL 18.11).
(PL
(PL 18.11).
(PL 18.11) and the
manuals4you.com manuals4you.com
A
• Ensure that the Finisher Gate moves freely. If the problem continues replace the Fin-
isher Gate (PL 18.11) and the Finisher Gate Solenoid
• Ensure that the Finisher Gate moves freely. If the problem continues replace the Fin-
isher Gate (PL 18.11) and the Finisher Gate Solenoid
Enter dC330 012-107 SCT Entrance Sensor. Manually actuate the SCT Exit Sensor actuator.
The display changes from L to H to L as the actuator moves in and out of the sensor.
Y N
The display is always H
Y N
Go to Flag 3 on BSD12.10. Check the harness for a short circuit to ground. If the
harness is good, replace the SCT Exit Sensor
+5 VDC is measured between P/J1078-1 and P/J1078-3 at the SCT Exit Sensor.
Y N
+5 VDC is measured between P/J1040-2 and P/J1040-3 on the Finisher PWB.
Y N
+5 VDC is measured between P/J1026-3 and P/J1026-2 on the Finisher
PWB.
Y N
+5 VDC is measured between P/J880-3 and P/J880-2.
Y N
Go to the +5VDC
short circuit.
Go to Flag 17 on BSD12.1 and check the harness for an open circuit.
Replace the Finisher PWB
Go to Flag 2 on BSD12.10 and check the harness for an open or a short circuit.
Replace or repair as required.
Go to Flag 3 on BSD12.10. Check the harness for an open circuit. If the harness is good,
replace the SCT Exit Sensor (PL
With paper at the sensor, less than +1 VDC is measured between P/J1040-1 and GND.
Y N
Replace the SCT Exit Sensor (PL
Check the following parts for wear, glazing, or slipping.
• Mailbox Entrance Roll (PL 18.10)
• Pinch Rollers (PL 18.12)
• SCT Exit Roll (PL 18.10)
• Drive Belt (PL 18.10)
Check the Drive Belt Tension Roll for proper tension.
1/05
8d-6
(PL 18.11).
(PL 18.11).
(PL 18.13).
Figure 1 wirenet and check wires for an open or
(PL 18.4).
18.13).
18.13).
DocuColor 12/DCCS50
Reissue