Table of Contents
Advertisement
Table 6 IDFE (MFY) Diagnostic LEDs - Normal Operation
Green Power LED (PWR)
Red Failure LED (ERR)
Amber Heartbeat LED (HB)
Amber 10/100 LED (100)
Green Activity LED (ACT)
Red LED
Red Failure LED
(ERR)
Amber Heartbeat
LED (HB)
Amber 100/10
Network LED
(100)
Figure 2 IDFE (MFY) Diagnostic LEDs
Status Indicator RAPs
OF19-1 IDFE Fault Entry RAP, 19-001 DC Power Fault
Energizes when DC Power is supplied to the
IDFE
Energizes when the power up sequence fails
Energizes when IDFE software is running
Energizes when the IDFE is connected to a
10/100BaseT Ethernet network Solid-ON
indicates 100mbps, LED-OFF indicates
10mbps connection
Energizes when network activity is occurring
over a 10/100 BaseT Ethernet Network
(Refer to
Table
5)
NOTE: The Green Link and Amber Diagnos-
tic LEDs only energize when the IDFE is
connected by a 10 or 100 BaseT Ethernet
Network connection.
Not Used
Red LED (not used)
Green Power LED
(PWR)
Green Activity LED
(ACT)
IDFE (MFY)
19-001 DC Power Fault RAP
NOTE: There are two configurations of the IDFE for this machine. They are identifiable by the
Product Code on the ID tag and by the number of Diagnostic LEDs. Early versions have 5
LEDs and are labeled Product Code GL2. Later versions have 6 LEDs and are labeled Product
Code MFY. This RAP applies generically to both. Where differences between the units exist,
the applicable information is followed by the product code for the specific IDFE.
A 19-001 fault is a DC Power failure to the IDFE. The green Power LED on the IDFE, when de-
energized, indicates a 19-001 fault.
Initial Actions
•
Refer to BSD 16.1.
NOTE: Before replacing any of the parts shown in BSD 16.1, ensure that the connectors
for the parts are correctly seated.
•
Inspect and re-seat DC wiring harness connector P/J899
plies DC power to the IDFE.
•
Refer to OF19-1 IDFE Fault Entry Rap,
LEDs and their locations.
Procedure
PO/PO the machine
(GP 8 IDFE Power OFF/Power ON (PO/PO)
switches off within 10 sec. of Power-On.
Y
N
If an intermittent fault is suspected, perform the following:
•
Go to
Flag 1
and
Flag 2
•
Open the IDFE (GL2 only) and ensure that the Connector for the LED PWBA is cor-
rectly seated.
•
Replace the Printer SSR
•
Replace the Printer LVPS
•
Replace the IDFE
(PL
•
Check for +5 VDC at,
(Flag
•
Check for +12 VDC at
(Flag
•
Go to
Flag 1
of BSD 16.1, and check for an open/short circuit.
•
Go to BSD16.1,
Flag
2, and check for an open/short circuit.
•
Replace the Printer SSR
•
Replace the Printer LVPS
•
Replace the IDFE
(PL
19.1).
1/05
2-230
manuals4you.com
manuals4you.com
(Flag
Figure 1
(GL2) or
Figure 2
). The green Power LED
of BSD 16.1. Check for loose connections.
(PL
9.3).
(PL
9.3).
19.1).
1,
Flag
2) 1 through 8.
1,
Flag
2) 9,11.
(PL
9.3).
(PL
9.3).
DocuColor 12/DCCS50
1). This connector sup-
(MFY), Diagnostic
Reissue
Advertisement
Table of Contents
Troubleshooting
