Xerox DocuColor 12/DCCS50 Service Manual page 781

Table 1 Input Component Control Codes
ID Description In_Out
007-189 TRAY CLOSED Input
SWITCH
007-190 HCF FEED HOT LINE Input
007-301 #1 TRAY SENSOR Input
007-308 HCF INTERLOCK Input
SWITCH
008-104 #1 PRE FEED SEN- Input
SOR
008-105 #1 FEED OUT SEN- Input
SOR
008-109 #2 PRE FEED SEN- Input
SOR
008-110 #2 FEED OUT SEN- Input
SOR
008-114 #3 PRE FEED SEN- Input
SOR
008-115 #3 FEED OUT SEN- Input
SOR
008-119 #4 PRE FEED SEN- Input
SOR
008-120 #4 FEED OUT SEN- Input
SOR
008-135 TRAY 5 FEED SEN- Input
SOR
008-150 TAKE AWAY SENSOR Input
008-153 PRE REGI SENSOR Input
008-155 REGI SENSOR Input
Reissue
DocuColor 12/DCCS50
Module_I
Smart Help D
High: Drawer / Tray is closed HCF
Low: Drawer / Tray is open.
Detects when the HCF paper
Drawer / Tray is closed.
Signal from the IOT to initiate paper HCF
feed from the HCF. In run mode a
high to low transition on this signal
will cause the HCF to feed paper. In
the diagnostic mode, this signal has
no effect on the HCF.
High: Tray Inserted Processor
Low: Tray out
High: HCF is docked HCF
Low: HCF is not docked.
Detects that the HCF is properly
docked to the IOT.
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: Paper Processor
Low: No Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
High: No Paper Processor
Low: Paper
Table 1 Input Component Control Codes
ID Description
008-163 BEHIND REGI JAM
SENSOR
008-198 TRANSPERENCY
(OHP) 1 SENSOR
008-199 OHP 2 SENSOR
008-221 #1 TRAY STACK
HEIGHT (LEVEL) SEN-
SOR
008-222 #2 TRAY STACK
HEIGHT (LEVEL) SEN-
SOR
008-223 #3 TRAY STACK
HEIGHT (LEVEL) SEN-
SOR
008-224 #4 TRAY STACK
HEIGHT (LEVEL) SEN-
SOR
008-226 #5 TRAY BYPASS)
STACK HEIGHT LEVEL
UP SENSOR
008-227 #5 TRAY (BYPASS)
STACK HEIGHT LEVEL
DOWN SENSOR
008-231 #1 TRAY NO PAPER
SENSOR
008-232 #2 TRAY NO PAPER
SENSOR
008-233 #3 TRAY NO PAPER
SENSOR
008-234 #4 TRAY NO PAPER
SENSOR
008-236 TRAY 5 PAPER SEN-
SOR
008-240 #2 TRAY SIZE S/W 1
1/05
6-101
In_Out Smart Help
Input High: No Paper
Low: Paper
Input High: No Transparency
Low: Transparency
Input High: No Transparency
Low: Transparency
Input High: Light block
Low: Light reception
Input High: Light block
Low: Light reception
Input High: Light block
Low: Light reception
Input High: Light block
Low: Light reception
Input Run #5 (Bypass) Nudger Roll Sole-
noid Simultaneously.
High: Lift up state
Low: Lift down State
Input High: Lift Down State
Low: Lift Up State
Input High: No Paper
Low: Paper
Input High: No Paper
Low: Paper
Input High: No Paper
Low: Paper
Input High: No Paper
Low: Paper
Input High: No Paper
Low: Paper
Input High: Switch on (soft data)
Cannot run with Tray 3 size switch
1,2,3,4
Cannot run with Tray 4 size switch
1,2,3,4
General Procedures
dC330 Component Control
Module_I
D
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor