Xerox DocuColor 12/DCCS50 Service Manual page 788

Table 2 Output Component Control Codes
ID Description In_Out
008-013 #2 FEED MOTOR CW Output
008-014 #2 TAKE AWAY FEED Output
CLUTCH
008-016 #3 NUDGER ROLL Output
SOLENOID
008-017 #3 FEED MOTOR CCW Output
008-018 #3 FEED MOTOR CW Output
008-019 #3 TAKE AWAY FEED Output
CLUTCH
008-021 #4 NUDGER ROLL Output
SOLENOID
008-022 #4 FEED MOTOR CCW Output
008-023 #4 FEED MOTOR CW Output
008-024 #4 TAKE AWAY FEED Output
CLUTCH
008-025 TAKE AWAY MOTOR Output
008-030 Tray 5 NUDGER ROLL Output
SOLENOID
008-037 TRAY 5 FEED CLUTCH Output
008-049 TRAY 5 LIFTER Output
MOTOR CCW (up)
008-042 TRAY 5 LIFTER Output
MOTOR CW (down)
008-043 MAIN MOTOR 2 Output
008-054 REGI MOTOR Output
General Procedures
dC330 Component Control
Module_I
Smart Help D
Motor normal rotation: Feed Roll Processor
rotation
On drives connection Processor
ON time is 2000 msec Processor
Motor reverse: Tray lift up (upper Processor
limit detection stop)
Does not turn on if the tray is not
set.
ON time: 6000 msec
Motor normal rotation: Feed roll Processor
rotation
On drives connection Processor
ON time is 2000 msec Processor
Motor reverse: Tray lift up (upper Processor
limit detection stop)
Does not turn on if the tray is not
set
ON time: 6000 msec
Motor normal rotation: Feed Roll Processor
rotation
On drives connection Processor
On (rotation) Processor
x Processor
On drives connection Processor
x Processor
Lower limit detection stop ON time: Processor
300 msec
Tray 5 Lift Motor CCW
On: Port (L) Processor
On: Port (L) Processor
Table 2 Output Component Control Codes
ID Description
009-011 CARTRIDGE MOTOR K Output
009-012 CARTRIDGE MOTOR Y Output
009-013 CARTRIDGE MOTOR
M
009-014 CARTRIDGE MOTOR
C
009-018 ROTARY LOCK MECH
LATCH
009-021 DEVE MOTOR
CLUTCH
009-025 IBT ROLL CONTACT
009-026 IBT ROLL RETRACT
009-031 DISPENSE MOTOR K
1/05
6-108
manuals4you.com manuals4you.com
In_Out Smart Help
Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), M (009-013), or C (009-
014)
Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors
M (009-013), C (009-014) or K
(009-011).
Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), C (009-014) or K (009-
011).
Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), C (009-013) or K (009-
011).
Output Latch - High: Rotary Lock SEL
RETN
Low: Rotary Lock SEL SUCF
Release - High: Rotary Lock SEL
RETN
Output On (High): Latch
Off (Low): Release
Output Run simultaneously with Main
Motor (004-007)
Automatically turns OFF after the
Roll Retract Home Position Sensor
detects the Contact Position (On:
Low, Off: High)
Output Run simultaneously with Main
Motor (004-007)
Automatically turns OFF after the
Roll Retract Home Position Sensor
detects the Retract Position (On:
Low, Off: High)
Output Start after moving the Rotary to the
K color and dispensing the toner.
NOTE: To drive the rotary, Move the
rotary to the K color in dC920
(Developer Unit Check).
DocuColor 12/DCCS50
Module_I
D
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Processor
Reissue